Frigidaire FLCE7522AW страница 52 Скачать руководство пользователя

Страница: 52 / 54

LIMITED WARRANTY

USA

1-800-374-4432

Frigidaire

10200 David Taylor Drive

Charlotte, NC 28262

Canada

1.800.265.8352

Electrolux Canada Corp.

5855 Terry Fox Way

Mississauga, Ontario, Canada

L5V 3E4

For the applicable warranty period as set forth below, as measured from your original date of

purchase, Electrolux will repair or replace any parts of this appliance that prove to be defective in

materials or workmanship when such appliance is installed, used and maintained in accordance

with the provided instructions.

Warranty Periods:

• All parts — One year including labor
• Wash tub — Functional life of the product (excluding labor)

Exclusions
This warranty does not cover the following:

1. Products with original serial numbers that have been removed, altered or cannot be readily

determined.

2. Product that has been transferred from its original owner to another party or removed

outside the USA or Canada.

3. Rust on the interior or exterior of the unit.

4. Products purchased “as-is” are not covered by this warranty.

5. Products used in a commercial setting.

6. Service calls which do not involve malfunction or defects in materials or workmanship, or

for appliances not in ordinary household use or used other than in accordance with the

provided instructions.

7. Service calls to correct the installation of your appliance or to instruct you how to use your

appliance.

8. Expenses for making the appliance accessible for servicing, such as removal of trim,

cupboards, shelves, etc., which are not a part of the appliance when it is shipped from the

factory.

9. Service calls to repair or replace appliance light bulbs, air filters, water filters, other

consumables, or knobs, handles, or other cosmetic parts.

10. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls,

tolls, ferry trip charges, or mileage expense for service calls to remote areas, including the

state of Alaska.

11. Damages to the finish of appliance or home incurred during installation, including but not

limited to floors, cabinets, walls, etc.

12. Damages caused by: services performed by unauthorized service companies; use of parts

other than genuine Electrolux parts or parts obtained from persons other than authorized

service companies; or external causes such as abuse, misuse, inadequate power supply,

accidents, fires, or acts of God.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

USTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT

REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,

INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE

LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE

YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH

AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS

WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO

NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR

LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS

MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY

ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

If You Need Service

Keep your receipt, delivery slip, or some other appropriate payment record to establish the

warranty period should service be required. If service is performed, it is in your best interest

to obtain and keep all receipts. Service under this warranty must be obtained by contacting

Electrolux at the addresses or phone numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux

Major Appliances North America, a division of Electrolux Home Products, Inc. In Canada, your appliance

is warranted by Electrolux Canada Corp. Electrolux authorizes no person to change or add to any

obligations under this warranty. Obligations for service and parts under this warranty must be performed

by Electrolux or an authorized service company. Product features or specifications as described or

illustrated are subject to change without notice.

Содержание FLCE7522AW























































Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды

Frigidaire FLCE7522AW, Инструкция по использованию и уходу

Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды