Frigidaire FLCE7522AW страница 21 Скачать руководство пользователя

Страница: 21 / 54

INSTALLATION

Grounding the electric dryer (USA)

For a grounded, cord-connected dryer:

1. The dryer MUST be grounded. In the

event of a malfunction or breakdown,

grounding will reduce the risk of

electrical shock by a path of least

resistance for electrical current.

2. After you purchase and install a

3-wire or 4-wire power supply cord

having an equipment-grounding

conductor and a grounding plug

that matches your wiring system,

the plug MUST be plugged into

an appropriate, copper wired

receptacle that is properly installed

and grounded in accordance with

all local codes and ordinances. If in

doubt, call a licensed electrician.

3. DO NOT modify the plug you’ve

installed on this appliance. If it will

not fit the outlet, have a proper outlet

installed by a qualified electrician.

For a permanently connected dryer:

The dryer MUST be connected to a

grounded metal, permanent wiring

system; or an equipment grounding

conductor must be run with the circuit

conductors and connected to the

equipment-grounding terminal or lead on

the appliance.

WARNING

ELECTRICAL SHOCK HAZARD

• A U.L.-approved strain relief must

be installed onto power cord. If the

strain relief is not attached, the cord

can be pulled out of the dryer and

can be cut by any movement of the

cord, resulting in electrical shock.

• DO NOT use an aluminum wired

receptacle with a copper wired

power cord and plug (or vice versa).

A chemical reaction occurs between

copper and aluminum and can cause

electrical shorts. The proper wiring and

receptacle is a copper wired power

cord with a copper wired receptacle.



NOTE

Dryers operating on 208 volt power

supply will have longer drying times

than dryers operating on 240 volt

power supply.



NOTE

The electric dryer has been designed

and certified to operate at both

240V and 208V. Drying times on a

208V power supply will, however, be

approximately 20% longer than drying

times on a 240V power supply. This

is normal and expected behavior and

applies to all drying cycles.



NOTE

A 208 or 240v, single phase 60Hz,

Alternating Current power supply

should be used on electric dryer

models as indicated on rating plate.

A 120v single phase 60Hz Alternating

Current power supply should be used

on gas dryer models as indicated on

rating plate.

WARNING

Improper grounding of the laundry

center may cause serious injury or

death. Check with a licensed electrician

if you are in doubt as to whether the

appliance is properly grounded.

Grounding the electric dryer

(Canada)

WARNING

Improper grounding of the laundry

center may cause serious injury or death.

Check with a licensed electrician if you

are in doubt as to whether the appliance

is properly grounded.

Содержание FLCE7522AW























































Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды

Frigidaire FLCE7522AW, Инструкция по использованию и уходу

Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды