Frigidaire FLCE7522AW Скачать руководство пользователя

Страница: 12 / 54

96"

(244cm)

max.

33"

(84cm)

min.

Exhaust system requirements

Duct work requirements

If your present system is made up of

plastic duct or metal foil duct, replace it

with a rigid or semi-rigid metal duct. Also,

ensure the present duct is free of any lint

prior to installing dryer duct.



NOTE

For installations requiring a longer

drain hose, have a qualified technician

install a longer drain hose (according to

your model number) available from an

authorized parts distributor. For drain

systems in the floor, install a siphon

break kit available from your local

hardware store.

WARNING

FIRE HAZARD

DO NOT

install a clothes dryer with

flexible plastic or metal foil venting

materials. Flexible venting materials are

known to collapse, be easily crushed

and trap lint. These conditions will

obstruct clothes dryer airflow and

increase the risk of fire.

Use only 4 inch (102 mm) diameter rigid

or flexible metal duct and approved vent

hood which has a swing-out damper(s)

that open when the dryer is in operation.

When the dryer stops, the dampers

automatically close to prevent drafts and

the entrance of insects and rodents. To

avoid restricting the outlet, maintain a

minimum of 12 inches (30.5 cm) clearance

between the vent hood and the ground

or any other obstruction.

WARNING

FIRE HAZARD

Failure to follow these instructions can create

excessive drying times and fire hazards.

The following are specific requirements for

proper and safe operation of your dryer.

Correct

Incorrect

Drain system requirements

1. Drain capable of eliminating 17 gals

(64.3 L) per minute.

2. A standpipe diameter of 1-1/4 in.

(3.18 cm) minimum.

3. Standpipe height above the floor

should be:

Minimum height: 33 in. (84 cm)

Maximum height: 96 in. (244 cm)

PRE-INSTALLATION REQUIREMENTS

Содержание FLCE7522AW























































Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды

Frigidaire FLCE7522AW, Инструкция по использованию и уходу

Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды