Frigidaire FLCE7522AW страница 49 Скачать руководство пользователя

Страница: 49 / 54

PROBLEM

POSSIBLE CAUSES

SOLUTIONS

No sound

from button

press or

end of cycle

notification

• The chime feature has been

muted

• Press and hold the Wash Temp

button for 3 seconds to unmute

the chime (on some models). Once

unmuted, the sound from the button

press and end of cycle reminder will

both be restored.

Dryer runs

but won’t

heat

• If 1 of the 2 fuses in the dryer

circuit is blown, the drum

may turn but the heater will

not operate (electric models).

• Gas supply valve is not open

(gas models).

• Dryer does not have enough

air supply to support the

burner flame (gas models).

• LP gas supply tank is empty

or there has been a utility

interruption of natural gas

(gas models).

• Replace fuse.

• Check to make sure supply valve is

open. See

Installation section for

procedure.

• See

Installation section.

• Refill or replace tank. Dryer should

heat when utility service is restored.

Drying cycle

takes too

long
Outside of

the

dryer feels

too hot or

smells hot

• Lint filter is clogged with lint.

• Exhaust duct requirements

have not been met.

• Electric dryer is connected to

a 208 volt circuit.

• Drying procedures not

followed.

• Outside exhaust hood or

exhaust duct may be clogged

or restricted.

• High humidity.

• Make sure all lint has been removed

from the dryer lint filter before

starting each cycle.

• Exhaust duct must be at least 4

inches in diameter and made of rigid

or semi-rigid metal.

• When in place, the duct must have

no more than three 90° bends and

must not exceed length listed in

Installation section.

• Drying time will be 20% longer when

drying on a 208 volt circuit than

when drying on a 240 volt circuit.

• See Operating Instructions.

• Clean out any obstruction.

• Use a dehumidifier near the dryer.

Before Calling (continued)

TROUBLESHOOTING

Содержание FLCE7522AW























































Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды

Frigidaire FLCE7522AW, Инструкция по использованию и уходу

Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды