Frigidaire FLCE7522AW страница 38 Скачать руководство пользователя

Страница: 38 / 54

Operating the dryer

STEPS

TIPS

IMPORTANT

1. Prepare load

for drying.

• Dry items of similar fabric, weight, and

construction in the same load.

• Separate dark items from light-colored

items. Separate items that shed lint from

those that attract lint.

• Check for stains which may not have been

removed in washing. Repeat stain removal

process and wash again before drying.

• Place delicate or small items in a mesh bag

(not included).

• Be sure buckles, buttons, and trim are

heatproof and won’t damage the drum

finish. Close zippers, buttons, hooks, and

hook and loop fasteners. Tie strings and

sashes to prevent snagging and tangling.

• Dryer heat may

permanently set

some stains.

2. Check that

the lint filter

is clean and

in place.

•

• DO NOT operate

dryer without lint

filter in place.

• DO NOT operate

dryer without

cleaning the filter

before use.

3. Load the

dryer and

close the

door.

• Load items loosely. The average wet load

will fill the drum 1/3 to 1/2 full. Items need

room to tumble freely for even drying and

less wrinkling.

• If desired, place a dryer fabric softener

sheet on top of the load at the beginning

of the cycle.

• When drying large items, dry only two or

three items at a time. Fill out the load with

smaller items.

• For delicate or very small loads, add two or

three similar items to improve tumbling action.

• DO NOT overload

the dryer.

WARNING

To reduce the risk of fire, electric shock

or injury to persons, read the Important

Safety Information in this

Use & Care

Guide before operating your dryer.

CAUTION

• DO NOT operate dryer without lint

filter in place.

• ALWAYS clean filter after each load.

OPERATING INSTRUCTIONS

Содержание FLCE7522AW























































Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды

Frigidaire FLCE7522AW, Инструкция по использованию и уходу

Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды