manualshive.com logo in svg

Freescale Semiconductor MCF54455, Справочное руководство

Поделиться
Скачать
Freescale Semiconductor MCF54455 Скачать руководство пользователя страница 785

DMA Serial Peripheral Interface (DSPI)

31-32

Freescale Semiconductor

31.4.4.4

Modified SPI Transfer Format (MTFE = 1, CPHA = 1)

Figure 31-18

 shows the modified transfer format for CPHA is set. Only the condition where CPOL is 

cleared is described. At the start of a transfer, the DSPI asserts the DSPI_PCS

n

 signal to the slave device. 

After the PCS to SCK delay has elapsed the master and the slave put data on their DSPI_SOUT pins at the 
first edge of DSPI_SCK. The slave samples the master DSPI_SOUT signal on the even numbered edges 
of DSPI_SCK. The master samples the slave DSPI_SOUT signal on the odd numbered DSPI_SCK edges 
starting with the third DSPI_SCK edge. The slave samples the last bit on the last edge of the DSPI_SCK. 
The master samples the last slave DSPI_SOUT bit one half DSPI_SCK cycle after the last edge of 
DSPI_SCK. No clock edge is visible on the master DSPI_SCK pin during the sampling of the last bit. The 
SCK to PCS delay must be greater or equal to half of the DSPI_SCK period.

NOTE

For correct operation of the modified transfer format, the user must 
thoroughly analyze the SPI link timing budget.

Figure 31-18. DSPI Modified Transfer Format (MTFE = 1, CPHA = 1, Fsck = Fsys/4)

31.4.4.5

Continuous Selection Format

Some peripherals must be deselected between every transfer. Other peripherals must remain selected 
between several sequential serial transfers. The continuous selection format provides the flexibility to 
handle both cases. The continuous selection format is enabled for the SPI configuration by setting the 
DSPI_PUSHR[CONT] bit.

When CONT is cleared, DSPI drives the asserted chip select signals to their idle states in between frames. 
The idle states of the chip select signals are selected by the DSPI_MCR[PCSIS] field. 

Figure 31-19

 shows 

the timing diagram for two four-bit transfers with CPHA set and CONT cleared.

t

CSC

 = PCS to SCK delay.

t

ASC

 = After SCK delay.

System Clock

1

2

3

4

5

6

DSPI_PCS

n

t

ASC

DSPI_SCK

Master Sample

Master DSPI_SOUT

Slave DSPI_SOUT

Slave Sample

t

CSC

Содержание MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды