manualshive.com logo in svg

Freescale Semiconductor MCF54455, Справочное руководство

Поделиться
Скачать
Freescale Semiconductor MCF54455 Скачать руководство пользователя страница 165

Cache

6-20

Freescale Semiconductor

cmpi.l

#4,d0

;flushed all the ways?

bne

setloop

rts

The following CACR loads assume: the instruction cache has been invalidated, the default instruction 
cache mode is cacheable, the default data cache mode is copyback. 

dataCacheLoadAndLock:

move.l

#0xa3080800,d0

; enable and invalidate data cache ...

movec

d0,cacr

; ... in the CACR

The following code segments preload half of the data cache (8 Kbytes). It assumes a contiguous block of 
data is to be mapped into the data cache, starting at a 0-modulo-8K address.

move.l

#512,d0

; 512 16-byte lines in 8K space

lea

data_,a0

; load pointer defining data area

dataCacheLoop:

tst.b

(a0)

; touch lo load into data cache

lea

16(a0),a0

; increment address to next line

subq.l

#1,d0

; decrement loop counter

bne.b

dataCacheLoop

; if done, then exit, else continue

; A 8K region has been loaded into ways 0 and 1 of the 16K data cache. lock it!

move.l

#0xaa088000,d0

; set the data cache lock bit ...

movec

d0,cacr

; ... in the CACR

rts

align

16

The following CACR loads assume the data cache has been previously invalidated, the default instruction 
cache mode is cacheable, and the default operand cache mode is copyback.

This function must be mapped into a cache-inhibited or SRAM space or these text lines are to be 
prefetched into the instruction cache. This may displace some of the 8-Kbyte space being explicitly 
fetched.

instructionCacheLoadAndLock:

move.l

#0xa2088100,d0

; enable and invalidate the instruction 

movec

d0,cacr

; cache in the CACR

The following code segments preload half of the instruction cache (8 Kbytes). It assumes a contiguous 
block of data is to be mapped into the cache, starting at a 0-modulo-8K address

move.l

#512,d0

; 512 16-byte lines in 8K space

lea

code_,a0

; load pointer defining code area

instCacheLoop:

intouch (a0)

; touch lo load into instruction cache

; Note in the assembler we use, there is no INTOUCH opcode. The following
; is used to produce the required binary representation

cpushl

#nc,(a0)

;touch lo load into 
;instruction cache

lea

16(a0),a0

;increment address to next line

subq.l

#1,d0

;decrement loop counter

bne.b

instCacheLoop

;if done, then exit, else continue

; A 8K region was loaded into levels 0 and 1 of the 16-Kbyte instruction cache. lock it!

move.l

#0xa2088800,d0

;set the instruction cache lock bit 

Содержание MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды