manualshive.com logo in svg

Freescale Semiconductor MCF54455, Справочное руководство

Поделиться
Скачать
Freescale Semiconductor MCF54455 Скачать руководство пользователя страница 242

Universal Serial Bus Interface – On-The-Go Module

Freescale Semiconductor

10-35

19–16

PTC

Port test control. Any value other than 0 indicates the port operates in test mode. Refer to Chapter 7 of the 

USB 

Specification Revision 2.0

 for details on each test mode.

0000 Not enabled.
0001 J_STATE
0010 K_STATE
0011 SEQ_NAK
0100 Packet
0101 FORCE_ENABLE_HS
0110 FORCE_ENABLE_FS
0111 FORCE_ENABLE_LS
Else  Reserved.

Note:

The FORCE_ENABLE_FS and FORCE ENABLE_LS settings are extensions to the test mode support in the 
EHCI specification. Writing the PTC field to any of the FORCE_ENABLE values forces the port into the 
connected and enabled state at the selected speed. Then clearing the PTC field allows the port state 
machines to progress normally from that point.

15–14

PIC

Port indicator control.For this device, this feature is not implemented, therefore this field is read-only and is always 
cleared.

13

PO

Port owner. Port owner handoff is not implemented in this design, therefore this bit is read-only and is always 
cleared.

12

PP

Port power. Represents the current setting of the port power control switch (0 equals off, 1 equals on). When power 
is not available on a port (PP = 0), it is non-functional and does not report attaches, detaches, etc.
When an over-current condition is detected on a powered port, the host controller driver from a 1to a 0 (removing 
power from the port) transitions the PP bit in each affected port.

11–10

LS

Line status. Reflects current logical levels of the USB DP (bit 11) and DM (bit 10) signal lines. In host mode, the line 
status by the host controller driver is not necessary (unlike EHCI) because hardware manages the connection of FS 
and LS. In device mode, LS by the device controller is not necessary.
00 SE0
01 J-state
10 K-state
11 Undefined

9

HSP

High speed port. Indicates if the host/device connected is in high speed mode.
0 FS or LS
1 HS

Note:

This bit is redundant with the PSPD bit field.

8

PR

Port reset. This field is cleared if the PP bit is cleared.
Host mode:

When software sets this bit the bus-reset sequence as defined in the 

USB Specification Revision 2.0

 starts. This 

bit automatically clears after the reset sequence completes. This behavior is different from EHCI where the host 
controller driver is required to clear this bit after the reset duration is timed in the driver.

Device mode:

This bit is a read-only status bit. Device reset from the USB bus is also indicated in the USBSTS register.

0 Port is not in reset.
1 Port is in reset.

Table 10-33. PORTSC1 Field Descriptions (continued)

Field

Description

Содержание MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды