Franklin Electric 5870205003C, Руководство пользователя

Страница: 25 / 136

SubDrive/MonoDrive Connect
25
6. Feed the 230 VAC power leads
through the larger opening on the
bottom left side of the SubDrive/
MonoDrive controller and connect
them to the terminals marked L1,
L2, and . Tighten terminals to
15 in-lbs (1.7 Nm).
7. For analog pressure transducer
or pressure sensor leads, use the
smaller opening on the bottom of
the SubDrive/MonoDrive unit (to the
right of the input power leads).
For Analog Pressure Transducer
NOTE: A 10-foot (3 m) section of
pressure transducer cable is provided with the controller. Other lengths are available. See
Accessories section for ordering information.
a. Locate the terminal block labeled TRANSDUCER (XDCR).
b. Connect the RED lead of the pressure transducer cable to the +24 terminal of the
XDCR terminal block.
c. Connect the BLACK lead of the pressure transducer cable to the - terminal.
d. Connect the bare shield lead of the pressure transducer cable to the S terminal
(where applicable).
e. Tighten terminals to 5 in-lbs (0.6 Nm) with a small screwdriver (provided).
f. Torque the fitting as shown in the figure to the right.
For SubDrive Pressure Sensor
a. Locate the terminal block labeled PRESSURE SENSOR (PS).
b. Connect the red and black leads (interchangeable) of the pressure sensor cable to
the terminals of the PS terminal block on the Pressure Input Board.
c. Tighten terminals to 5 in-lbs (0.6 Nm) with a small screwdriver (provided).
d. Torque the fitting as shown in the figure to the right.
s
CAUTION
!
For retrofit application (i.e. MonoDrive), make sure to check integrity of power and motor leads.
This requires measuring the insulation resistance with the suitable megohmmeter.
* See AIM Manual for specifications.
YEL RED BLK
L2 L1
WARNING – Retain Owner’s Manual.
Installation and operation of this equipment
requires detailed instructions as provided in
the Owner’s Manual.
AVERTISSEMENT - Conserver le manuel du
propriétaire. L’installation et le
fonctionnement de cet équipement
nécessite des instructions détaillées fournies
dans le manuel du propriétaire.
ADVERTENCIA – Conserve el Manual de
Usuario. Para la apropiada instalación y
operación de este producto, se requiere
seguir detalladas instrucciones contenidas
en el Manual del Usuario.
Use 75 ºC CU wire rated 600 V min
Utilisez un fil nominale classifier
75 °C CU / 600 V min
Use alambre de 75 °C CU con
una clasificación mínima de
600 V.
Suitable for use on a circuit
capable of delivering not more
than 5000 rms symmetrical
amperes, 250 V maximum. Use 75
ºC CU wire rate 300 V min.
Convenable pour utilisation sur un
circuit capable de livrer pas plus
de 5000 ampères symétriques
pae, 250 V maximum. Utilisez un fil
nominale classifier 75 °C CU /
300 V min
Adecuado para utilizarse en un
circuito capaz de entregar no más
de 5.000 amperes RMS
simétricos, 250 V como máximo.
Use alambre de 75 °C CU con una
clasificación mínima de 300 V.
Tighten terminals to 15 in-lbs.
Serrer les terminaux à 15 po-lb
Apriete las terminales a
15 pulgadas-libra.
A
AUX INPUT
PRESSURE
SENSOR
+24 _ S NC COM NO
ALARM RELAY
NC COM NO
RUN RELAY TRANSDUCER
R2 R1 PS A1 XDCR
J1
J6
+24 A B | + |
_
ALTERNATOR WET SENSOR
WS
C2 C1
J5
Tighten terminals to 15 in-lbs.
Serrer les terminaux à 15 po-lb
Apriete las terminales a
15 pulgadas-libra.
J3
J4
R69
R69 R49 R54
D13
C47 R95
R96
R93
R94
TP78
TP76
R88
TP77
C11 R91
R40
R102
D10
C49
R97
TP83
Q7
R103
TP80
TP82
R100
R99
R104
D15
C50
C7
U3
C46
D5
U10
R90
C12
R20
R89
C8
D16
R105
Q6
TP81
R98
R101
TP79
C6
R55 R56
TP71
U7
C2
C33
C4
P1
RoHS
Compliant
IMAG
94V-0
BD02
38 15
226649101 R
IN
s
CAUTION
!
When increasing the pressure, do not exceed the mechanical stop on the pressure sensor
or 80 psi (5.5 bar). The pressure sensor may be damaged.