background image

RETRO 

 

 

 

 

 

Complete your home security with 

a Foresee gate automation set 

PICO

  

sliding gate motors for confined spac-

es, sloping drives, and sharp corners 

AVANTI

  

 

 

 

 

 

Warranty  

 

Warranty  covers  defects  to  the  Foresee  product  proven 
attributable  to  a  material  or  manufacturing  fault  during  the 
warranty  period.  We  will  repair,  or  refund,  or  replace  faulty 
product with a similar fault free product at our discretion. We 
do  not  accept  costs  for  dismantling,  installation,  or  for 
carriage.  Parts  replaced  under  warranty  are  the  property  of 
the warrantor. 
 

 

The warranty period for Radio Equipment is 24 months. The 
period for replacement parts is 6 months or to the end of the 
current warranty period, which ever is longer.   

 
Warranty exceptions 

 

The warranty does not cover damage caused through:  
Wear  &  Tear  or  Improper  Installation  or  Negligent  Care  or 
lack of Maintenance or Misuse or Water ingress or Abnormal 
Environmental  Influences  or  Mechanical  damage  during 
Transport  or  damage  through  improper  Installation  or 

PRIMO

  

Garage door opener  

Содержание AXEL F730





















Отзывы: