7
The appliance features a hinge assembly which is supplied pre-
assembled. The hinge assembly should be fitted onto the rear of the
glass facia, on the lower right hand side as follows;
1) Before fitting the glass facia to the fire, attach the short end to the
bracket on the rear of the glass facia using the screw, nut and nylon
washer provided.
2) Attach the long end of the hinge to the stud as shown. Secure using
the nut provided. All nuts should be tightened fully, and then released
one quarter of a turn.
After commissioning the appliance, the customer should be instructed
on the safe use of the appliance and the need for regular servicing.
Frequency of service depends on usage, but MUST be carried out at
least once annually.
Advise that cleaning of the fire may be achieved when the fire is cold
using a damp cloth and mild detergent on most surfaces.
Advise that the fire will emit a "newness" smell for a time after initial
commissioning and that extra ventilation may be needed during this
time. Recommend that a guard be used for the protection of the young,
pets, the elderly and the infirm.
Isolate the fire from the gas supply. Ensure that the fire is fully cold
before attempting service. A suggested procedure for servicing is
detailed as follows;
1.
Lay out the dustsheet and tools.
2.
Remove the front glass facia as described in section 15.0,
only in reverse.
3.
Remove the glass door assembly (4 screws) and clean
carefully. Remove the valve cover plate (4 screws).
4.
Inspect the burner and the catalysts and clean if necessary
with a soft brush.
5.
Disconnect the gas supply.
6.
Undo the four screws retaining the burner support brackets
to
the base and rear of the firebox.
7.
Remove the burner unit, strip off the burner pipes and clean
thoroughly.
8.
Clean the in-line restrictor, pilot assembly and the burner
tube. Do not attempt to remove the pilot injector as this can
cause damage.
9. Re-assemble
components.
10.
Turn on the gas supply and leak test. Check pilot and
burner for good ignition.
11.
Refit the valve cover and retaining screws.
12.
Refit the glass door assembly, ensuring a good seal.
13.
Refit the facia Refitting as described in section 15.0.
14.
Check the purpose provided ventilation is unobstructed.
15.
Light the fire and test setting pressures.
16.
Check safe operation of the appliance.
For specific servicing instructions, see relevant sections.
First, remove the front Glass facia as described in Section 15.0 only in
reverse, remove the valve cover (4 screws) and disconnect the gas
connection inside appliance. The gas connections to the gas valve can
now be released. Undo the four screws retaining the burner brackets to
the base and rear of the firebox. The burner may now be removed.
Remove the pilot and main burner pipes and blow through to dislodge
any debris. Now remove the in line restrictor and blow through to make
sure it is entirely clear.
Unclip the pilot lint gauze and clean with a soft brush. Clean the
exterior of the pilot assembly with a soft brush and blow through the
flame ports on the pilot head. Check the aeration holes are free from
lint or dirt. The pilot assembly can be removed if required by
disconnecting the electrode HT lead, gas pipe, thermocouple lead and
unscrewing the mounting screws and lifting away.
16.0 BRIEFING THE CUSTOMER
WARNING: DO NOT ADD LOGS OR ORNAMENTS
SUCH AS PINE CONES, VERMICULITE OR ROCK
WOOL. USING THESE ADDED ITEMS CAN CAUSE
SOOTING.
17.0 SERVICING
18.0 SERVICING THE BURNER
WARNING: ANY CHANGE TO THIS HEATER OR ITS
CONTROLS CAN BE DANGEROUS.
M4 nyloc nut
Nylon washer
Retaining stud
M4 screw
15.0 FITTING THE GLASS FACIA (continued)
