Flavor Burst TS 44BEV Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 100

background image

56

Installing the Injector System and
Suspension Bracket

1. Determine how the Blending Assembly will

be positioned on the freezer. When
possible, follow the recommendations
outlined above.

2. Rearrange the Suspension Bracket

assembly so that it is placed on the outer
side of the Blending Assembly, with the
open end of the bracket hook facing toward
the center of the freezer. Ensure all parts
are assembled in the proper order.

NOTE:

THE PLASTIC WASHER SHOULD

ALWAYS BE BETWEEN THE BRACKET
KNOB AND THE UPPER BRACKET.

NOTE:

THE UPPER BRACKET SHOULD

ALWAYS BE INSTALLED TO THE OUTSIDE
OF THE BRACKET BASE.

NOTE:

THE SPRING WASHER SHOULD BE

BETWEEN THE UPPER BRACKET AND THE
BRACKET BASE.

NOTE:

THE BRACKET THUMB SCREW

SHOULD ALWAYS BE INSERTED THROUGH
THE UPPER BRACKET FIRST AND THEN
SCREWED INTO THE BRACKET BASE,
PLACING IT ON THE OUTSIDE OF THE
BRACKET ASSEMBLY.

NOTE:

THE HOOK OF THE UPPER

BRACKET CAN BE FACING EITHER
DIRECTION ACCORDING TO PREFERENCE.

3. Hang the Suspension Bracket on the lower

door post and install the Blending Assembly
on the preferred side of the freezer. Install
the Blending Head locking ring fully over the
Spout Adapter so that the locking collar
covers the tabs on the Adapter and rotate
the locking collar to secure.

4. Connect the Drive Motor cable to the Drive

Motor.

5. Use the Gear Box thumb nut to adjust the

Suspension Bracket horizontally so that it
hangs straight down from the door nut.

«
...
55
56
57
58
59
...
»

Содержание TS 44BEV





































































































Отзывы:

Нет отзывов

Похожие инструкции для TS 44BEV

Бренд: Hamilton Beach Страницы: 15

EZ Multi-Cone 1W

Бренд: rosseto Страницы: 4

Бренд: Live Fine Страницы: 12

Бренд: Pallas Страницы: 21

Thermaltake PW850i

Бренд: Conrad Страницы: 4

Бренд: Curtis Страницы: 5

Бренд: Haws Страницы: 6

Бренд: Bobrick Страницы: 2

OLK-W-01 Eco Laundry

Бренд: Wowtech Страницы: 9

Бренд: Lacava Страницы: 10

Бренд: EOS Hitech Страницы: 14

Бренд: Selecto Страницы: 7

Бренд: Igloo Страницы: 6

Бренд: Igloo Страницы: 6

Бренд: Igloo Страницы: 10

Бренд: Bunn Страницы: 27

Бренд: Perlick Страницы: 125

Бренд: U-Line Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды