Flavor Burst TS 44BEV Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 100

background image

52

Installing the ELE 510 Spigot Switch
Internally on a Taylor 428 / 432 Freezer.

Flavor Burst highly recommends integrated
switches be installed to power the TS 44BEV
system.

However, if no integrated switches are

available at the time of installation, use the
ELE 510 external switch included with this
system. The ELE 510 can also be mounted
inside the front panel of Taylor 428 and 432
models as directed below.

NOTE:

ENSURE THE FREEZER IS TURNED

OFF AN UNPLUGGED TO AVOID ANY
ELECTRICAL SHOCK WHEN WORKING
WITHIN THE TAYLOR 428 / 432 PANEL BOX.

1. Remove the Touchscreen Assembly from

the mounting plate.

2. Unscrew and remove the front panel from

the Taylor 428 or 432 freezer.

3. Attach one small square pieces of adhesive

to front bottom of the flat bracket piece that
comes with the ELE 510 switch. Attach
another piece of adhesive to the upper end
of the bracket on the other side. Then,
attach the switch behind that upper
adhesive piece as shown, with the switch
lever pointing to the right.

4. Attach the switch assembly just left of the

Taylor internal switch, to the inside of the
cover plate. The ELE 510 switch lever
should be just above the internal draw pin
as shown.

5. With the freezer turned off and with no

product in the freezer, pull the handle into
the open position to see if the draw pin
depresses the switch lever. If not, reposition
the switch so that it makes full contact.

NOTE:

THE SWITCH MUST BE POSITIONED

SO THAT THE SWITCH LEVER IS FULLY
DEPRESSED WHEN THE DRAW HANDLE IS
IN THE OPEN POSITION.

«
...
51
52
53
54
55
...
»

Содержание TS 44BEV





































































































Отзывы:

Нет отзывов

Похожие инструкции для TS 44BEV

Бренд: Tach-It Страницы: 8

Бренд: RainSoft Страницы: 44

Бренд: Precision Страницы: 15

Бренд: Yaesu Страницы: 16

ARCTIC COMPACT 12-20 UL

Бренд: Cecilware Страницы: 16

Comfortemp 99340

Бренд: Trebs Страницы: 38

HAC8EECQ 1E Series

Бренд: Halsey Taylor Страницы: 6

Commercial COOL CCBL01

Бренд: W APPLIANCE Страницы: 16

Бренд: Viqua Страницы: 4

Бренд: Sharper Image Страницы: 6

Бренд: Haws Страницы: 4

Бренд: Haws Страницы: 6

ConturaSeries B-4063

Бренд: Bobrick Страницы: 2

Бренд: Bobrick Страницы: 2

Бренд: Bobrick Страницы: 4

Бренд: AOX Страницы: 4

Бренд: Sharper Image Страницы: 6

Бренд: Kimberly-Clark Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды