Flavor Burst TS 44BEV Скачать руководство пользователя страница 96

Страница: 96 / 100

Reformatting the SD Card

If the Touchscreen file upload fails, you may
need to reformat the SD card.

IMPORTANT:

Reformatting the card will erase everything
on the card

so be sure to back up all the SD

card files to a folder on your computer’s hard
drive before proceeding.

1. To format your card, ensure the switch on

the card is in the locked position and insert
it into a card reader on your computer.

2. Click on My Computer and open the drive

that contains the SD card.

3. Create a backup folder on your computer

and copy all the SD card files into that
folder.

4. Go back to My Computer and right click on

the SD card drive. S

elect “Format” from the

list.

NOTE:

BE SURE TO CLICK ONLY THE

DRIVE WITH THE SD CARD. IT IS POSSIBLE
TO ERASE YOUR COMPUTER’S HARD
DRIVE CONTENTS IF YOU CLICK ON THE
INCORRECT DRIVE.

5. Accept the default settings, but be sure that

“quick format” is not selected. Then click the
start button.

6. After reformatting, copy the files from the

Backup folder that you wish to update back
onto your card. Repeat the section
UPLOADING THE TOUCHSCREEN
LABELS.

Содержание TS 44BEV





































































































Результаты поиска

Содержание TS 44BEV

Отзывы:

Похожие инструкции для TS 44BEV

Бренды по названию

Популярные бренды

Flavor Burst TS 44BEV, Руководство пользователя

Результаты поиска

Содержание TS 44BEV

Отзывы:

Похожие инструкции для TS 44BEV

Бренды по названию

Популярные бренды