Flavor Burst TS 44BEV Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 100

background image

34

NOTE:

THE FOLLOWING PROCEDURES

ARE PERFORMED LESS FREQUENTLY
THAN DAILY OR AS NEEDED.

Clean-In-Place (CIP) Procedure

The Clean-In-Place procedure should be
performed every 30 days to ensure that the
syrup passageways are free of any product
crystallization.  The medium used for this
process must be an approved sanitizing product
mixed according to the product manufacturer’s
instructions.

This Clean-In-Place procedure is detailed in
three phases:
(1) 9-Tube Assembly Cleaning
(2) Syrup System Cleaning
(3) Reassembly
To ensure maximum results, the following
instructions should be completed in sequence
as stated.  This will expose the system and
parts to the sanitizing medium for about 130
minutes.

CIP - Phase 1: 9-Tube Assembly Cleaning

1. Mix approved detergent with warm water

according to manufacturer’s instructions.
Also prepare approved sanitizer solution
according to manufacturer’s instructions.

2. Unlock and remove the 9-Tube Assemblies

from each Blending Head syrup line
opening.

3. Remove each Coupler Body by rotating and

unlocking them from the Coupler Bases.

4. Remove the Syrup Line Manifolds from the

tube connector bodies, then remove the
Duckbill Check Valves from each Syrup
Line Manifold.

5. Place the ends of both 9-Tube Assemblies

into a container to catch the expelled syrup
and sanitizer solution during the Clean-In-
Place procedure.

SCHEDULED MAINTENANCE

«
...
33
34
35
36
37
...
»

Содержание TS 44BEV





































































































Отзывы:

Нет отзывов

Похожие инструкции для TS 44BEV

Бренд: Daewoo Страницы: 9

Бренд: U-Line Страницы: 22

Бренд: Oasis Страницы: 14

Бренд: kbice Страницы: 19

Бренд: Parweld Страницы: 12

Бренд: Kobra Страницы: 64

ARCTIC Compact 12L

Бренд: Ugolini Страницы: 28

Бренд: Igloo Страницы: 1

Бренд: Pioneer Страницы: 12

Бренд: Accucold Страницы: 23

Бренд: Super Страницы: 13

Бренд: GRG Banking Страницы: 11

Бренд: physa Страницы: 5

Бренд: BOWMAN Страницы: 3

Бренд: Waring Страницы: 44

Бренд: SereneLife Страницы: 8

KLEENEX REVEAL H-7855

Бренд: U-Line Страницы: 3

Rubbermaid H-3542

Бренд: U-Line Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды