Flavor Burst TS 44BEV Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 100

background image

48

Installing the Spout Adapter

Every TS 44BEV system ships with a standard
Blending Adapter common to most freezers.
However, additional adapters are available for
use with other models & freezer manufacturers.
Since the fitting is tight, install the Adapter with
the freezer door removed. Replacements are
available in the Spare Parts Kit.

1. Ensure that the Spout Adapter has been

sanitized according to instructions in the
SCHEDULED MAINTENANCE section.
Then lube and install both o-rings in their
proper places on the Spout Adapter.

2. Clean the freezer door and spout according

to manufacturer’s instructions before
installing the Spout Adapter on the freezer
door.

3. Set the Adapter on a flat, clean surface, and

then place the freezer door spout upright
onto the Adapter. Rock the freezer door
forward to snap the Adapter into place.

4. Return the door to the freezer with the

Spout Adapter attached.

5. Repeat Steps 1-4 to install the Spout

Adapter on the other freezer.

Installing the Touchscreen and Mounting
Bracket

The Touchscreen is the control unit for the
Flavor Burst

®

system. Normal operating

functions are performed using the Touchscreen
and the freezer draw handle. The Touchscreen
is mounted to the top of the freezer with the
Touchscreen Mounting Bracket.

1. Clean, rinse and dry the top surface of the

freezer between the front edge and the
hopper. This area is where the
Touchscreen will be mounted.

NOTE:

WHEN USING TWO FREEZERS,

MOUNT THE TOUCHSCREEN ON THE LEFT
FREEZER IF POSSIBLE.

2. Place the assembled Touchscreen and

bracket onto the top edge of the freezer. If
installing the TS 44BEV system on two
separate freezers, install the Touchscreen
on the left freezer, centered above the
draw-handle.  If installing on a single, multi-
barrel freezer, center the Touchscreen on
the freezer.  The bottom plate of the bracket
should sit fully on the surface of the freezer
between the front edge and the hopper
cover.  Mark around the plate with a pencil.

EQUIPMENT SETUP

«
...
47
48
49
50
51
...
»

Содержание TS 44BEV





































































































Отзывы:

Нет отзывов

Похожие инструкции для TS 44BEV

Бренд: CAB Страницы: 12

Бренд: aidapt Страницы: 2

Maestrale Jolly 12

Бренд: Bras Страницы: 32

Бренд: Ratiomed Страницы: 2

Бренд: Keg King Страницы: 5

Pure Water SmartStream UV PWA002

Бренд: Watts Страницы: 10

Бренд: La Sommeliere Страницы: 51

Бренд: Grindmaster Страницы: 72

Бренд: Clean Water Systems Страницы: 18

Бренд: Itouchless Страницы: 2

Бренд: DE VECCHI Страницы: 5

Бренд: TECNICOMAR Страницы: 86

Бренд: DRIFTON Страницы: 10

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 6

Бренд: U-Line Страницы: 9

Бренд: U-Line Страницы: 20

Better Pack 555eS

Бренд: U-Line Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды