FläktGroup eCO Premium Скачать руководство пользователя страница 45

Страница: 45 / 48

eCO Premium™ - Installation & Maintenance

FläktGroup DC_9604GB_20190327_R6

Specifications are subject to alteration without notice

26. TROUBLE SHOOTING (GENERAL)

Fault

Possible Cause

Suggested Action

Unit is difficult to start

Reduced supply voltage

Ensure voltage is consistent with motor name plate data

Insufficient air capacity

Clogged ductwork and/or extract points Clean ductwork and suction point

Insufficient pressure

Clogged impeller

Clean impeller

Dirty filter

Clean or replace filter media. Note: always use original media
type to guarantee unit performance.

Insufficient rotation speed

Check Supply Voltage and if necessary, correct.

Clogged heat exchanger

Clean heat exchanger block

Airflow Performance
drops after a period of
acceptable operation.
(See above)

Air leak before and/or after the fan

Damaged impeller

Check connections and unit casing and restore to original
“as installed” condition.

Check impeller. If necessary, replace with an original spare part

Heat Exchanger Discharge
air temperature too low

External air lower than –5° C

Employ a post heating device

Insufficient Heat
Exchanger performance

Build up of dirt on Heat Exchange fins

Clean Heat exchanger

Frost formation on

External air inferior to -5°C

Employ a pre heating device (frost protection heater)

Heat Exchanger

Airflow hunting

Clogged or wrong ductwork connection

Modify the ductwork and/or replace fan.

Clean and/or replace the suction duct

TROUBLE SHOOTING

Содержание eCO Premium

















































Результаты поиска

Содержание eCO Premium

Отзывы:

Похожие инструкции для eCO Premium

Бренды по названию

Популярные бренды

FläktGroup eCO Premium, Руководство по установке и обслуживанию

Результаты поиска

Содержание eCO Premium

Отзывы:

Похожие инструкции для eCO Premium

Бренды по названию

Популярные бренды