Fisher Scientific accuSpin 3 страница 50 Скачать руководство пользователя

Страница: 50 / 82

Maintenance and care

During cleaning liquids and espe-
cially organic solvents should not
come into contact with the drive
shaft and the ball bearing.
Organic solvents may decompose
the lubricant of the motor bearing.
The drive shaft may block.

Instruments with refrigeration unit:

If a strong ice sheet is present in the internal
chamber, be sure to remove all condensate
after defrosting!

Please control and clean the venting slots
regularly!

Before cleaning the venting slots
please disconnect the centrifuge
from the mains supply.
Please pull mains plug!

Disinfection

If a centrifuge tube containing infectious material leaks
during a run, you have to disinfect the centrifuge im-
mediately.

Infectious material could enter the centri-
fuge if spills or tube breakage occur

Danger of infection may occur upon
contact

Take appropriate protective meas-

ures for personnel!

Mind the permissible filling volumes and
loading limits for the tubes

In case of contamination the operator has
to make sure, that no further persons are
jeopardized

Contaminated parts have to be decontami-
nated immediately

If required further protective measures
have to be initiated

Содержание accuSpin 3



















































































Результаты поиска

Содержание accuSpin 3

Отзывы:

Похожие инструкции для accuSpin 3

Бренды по названию

Популярные бренды

Fisher Scientific accuSpin 3, Руководство по эксплуатации

Результаты поиска

Содержание accuSpin 3

Отзывы:

Похожие инструкции для accuSpin 3

Бренды по названию

Популярные бренды