FFC V-Snow Blade Скачать руководство пользователя страница 9

Страница: 9 / 47

SAFETY DECALS & LABELS

Use part numbers to order replacements for lost or damaged decals. Be sure to read all decals before

operating the attachment. They contain information you need to know for both safety and longevity.

Placement or replacement of Safety Signs

1. Clean the

area of application with nonflammable solvent, and then wash the same area with soap and water.

2. Allow the surface to fully dry.

3. Remove the backing from the safety sign, exposing the adhesive surface.

4. Apply the safety sign to the position shown in the diagram above and smooth out any bubbles.

Instructions

Keep all safety signs clean and legible.

2. Replace all missing, illegible, or damaged safety signs.

3. Replacement parts, for parts with safety signs attached, must also have safety signs attached.

4. Safety signs are available, free of charge, from your dealer or from SWEEPSTER.

Item Part

Qty Description

50-0721

3 Label, Warning, Crush Hazard

2. RDL3132

2 Label, Amber, Reflective Tape, 2 x 6

3. RDL3131

2 Label, Red, Reflective Tape, 2 x 6

50-0724

1 Label, Warning, High Pressure Fluid

50-0737

1 Label, Warning, Pinch Point Hazard

50-10017

1 Label, Warning, Avoid Serious Injury

50-0775

2 Label, Warning, Crush Hazard

4. 50-0724

1. 50-0721

5. 50-0737

6. 50-10017

9. 50-0775

2. & 3. RDL3132 & RDL3131

Serial

Number Tag

Содержание V-Snow Blade
















































Результаты поиска

Содержание V-Snow Blade

Отзывы:

Похожие инструкции для V-Snow Blade

Бренды по названию

Популярные бренды

FFC V-Snow Blade, Руководство оператора

Результаты поиска

Содержание V-Snow Blade

Отзывы:

Похожие инструкции для V-Snow Blade

Бренды по названию

Популярные бренды