FFC V-Snow Blade Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 47

FFC V-Snow Blade Скачать руководство пользователя страница 21

21

OPERATION

General Storage:

NOTICE!

Do not store in direct sunlight. Materials will deteriorate prematurely if stored in direct

sunlight. Do not store near intense heat.

Storage:

• Clean the unit thoroughly, removing all mud, dirt and grease.

• Inspect for visible signs of wear, breakage or damage. Order any parts required and make the

necessary repairs to avoid delays upon removal from storage.

• Tighten loose nuts, capscrews and hydraulic connections.

• Coat exposed portions of the cylinder rods with grease.

• Lubricate grease fittings.

• Seal hydraulic system from contaminants and secure all hydraulic hoses off the ground to help prevent

damage.

• Store unit in a dry and protected place. Leaving the unit outside will materially shorten its life.

Additional Precautions for Long Term Storage:

• Touch up all unpainted surfaces with paint to avoid rust.

• Inflate tires to recommended tire pressure.

• Fill fuel tank and hydraulic oil tank to maximum.

• Check antifreeze properties and drain fluids as appropriate.

Removal from Storage:

• Remove cover.

• Wash unit and replace any damage and/or missing parts.

• Lubricate grease fittings.

• Check hydraulic hoses for damage and replace as necessary.

«
...
19
20
21
22
23
...
»

Содержание V-Snow Blade
















































Отзывы:

Нет отзывов