background image

27

MAINTENANCE 

Installing New Polyurethane Wear Edges

NOTICE! 

All nuts and bolts must be installed using proper torque specifications (refer to Bolt 

Torque Specifications).

NOTICE! 

Improper installation of edges will result in damage to plowing surface and premature 

wearing of edges.

1.  Park prime mover on a firm, level surface with blade properly attached.

2.  Lower the blades cutting edge onto a sturdy wood or metal blocking,  positioned under the pivoting 

assembly, to safely hold the wear edge 6 to 8 inches above the level surface.

3.  Place primer mover in “Park” and engage parking brake.

4.  Remove and retain all nuts and bolts but the ones at each end of the wear edge.

5.  Support one end of the wear edge, remove the nut and bolt, then lower it to the level surface.

6.  Support the other end, remove the nut and bolt and lower to the level surface.

7.  Store wear edges and all nuts and bolts for possible future use.

8.  Support one end of the new wear edge and install with a new nut and bolt.

9.  Support the other end and install a new nut and bolt

10. Install all new nuts and bolts.

11. Repeat steps 4-10 for other wear edge.

12. Install center rubber wear edge and plates with new nuts and bolts.

NOTICE! 

When installing nuts and bolts on center rubber wear edge, DO NOT tighten to 

specified torque. Tighten until the retaining plate has slightly compressed the rubber.

Содержание V-Snow Blade
















































Отзывы: