background image

47

WARRANTY

Limited Warranty

Except for the Excluded Products as described below, all new products are warranted to be free from defects 

in material and/or workmanship during the Warranty Period, in accordance with and subject to the terms and 

conditions of this Limited Warranty.  

1. 

Excluded Products.  The following products are excluded from this Limited Warranty:

(a)  Any cable, part that engages with the ground (i.e. sprockets), digging chain, bearing, teeth, tamping 

and/or demolition head, blade cutting edge, pilot bit, auger teeth and broom brush that either constitutes or is part 

of a product.

(b)  Any product, merchandise or component that, in the opinion of Paladin Light Construction

1

, has been 

(i) misused; (ii) modifi ed in any unauthorized manner; (iii) altered; (iv) damaged; (v) involved in an accident; or (vi) 

repaired using parts not obtained through Paladin Light Construction.

 

2. 

Warranty Period.  The Limited Warranty is provided only to those defects that occur during the Warranty 

Period, which is the period that begins on the 

fi rst to occur

 of: (i) the date of initial purchase by an end-user, (ii) the 

date the product is fi rst leased or rented, or (iii) the date that is six (6) months after the date of shipment by Paladin 

Light Construction as evidenced by the invoiced shipment date (the “Commencement Date”) and ends on the date 

that is twelve (12) months after the Commencement Date.

3. 

Terms and Conditions of Limited Warranty.  The following terms and conditions apply to the Limited Warranty 

hereby provided:

 (a) 

Option to Repair or Replace. Paladin Light Construction shall have the option to repair or replace 

the product.

(b) 

Timely Repair and Notice.  In order to obtain the Limited Warranty, (i) the product must be repaired 

within thirty (30) days from the date of failure, and (ii) a claim under the warranty must be submitted to Paladin Light 

Construction in writing within thirty (30) days from the date of repair. 

 (c) 

Return of Defective Part or Product.  If requested by Paladin Light Construction, the alleged 

defective part or product shall be shipped to Paladin Light Construction at its manufacturing facility or other location 

specifi ed by Paladin Light Construction, with freight PRE-PAID by the claimant, to allow Paladin Light Construction 

to inspect the part or product. 

Claims that fail to comply with any of the above terms and conditions shall be denied. 

LIMITATIONS AND EXCLUSIONS

.

THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING 

WITHOUT LIMITATION THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE 

AND ANY WARRANTY BASED ON A COURSE OF DEALING OR USAGE OF TRADE.

IN NO EVENT SHALL PALADIN LIGHT CONSTRUCTION BE LIABLE FOR CONSEQUENTIAL OR SPECIAL 

DAMAGES.

IN NO EVENT SHALL PALADIN LIGHT CONSTRUCTION BE LIABLE FOR ANY LOSS OR CLAIM IN AN 

AMOUNT IN EXCESS OF THE PURCHASE PRICE, OR, AT THE OPTION OF PALADIN LIGHT CONSTRUCTION, 

THE REPAIR OR REPLACEMENT, OF THE PARTICULAR PRODUCT ON WHICH ANY CLAIM OF LOSS OR 

DAMAGE IS BASED.  THIS LIMITATION OF LIABILITY APPLIES IRRESPECTIVE OF WHETHER THE CLAIM 

IS BASED ON BREACH OF CONTRACT, BREACH OF WARRANTY, NEGLIGENCE OR OTHER CAUSE AND 

WHETHER THE ALLEGED DEFECT IS DISCOVERABLE OR LATENT.  

1

Attachment Technologies Inc., a subsidiary of Paladin Brands Holding, Inc. (PBHI) is referred to herein as Paladin Light 

Construction.

February 10, 2010

Содержание V-Snow Blade
















































Отзывы: