FFC V-Snow Blade Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 47

FFC V-Snow Blade Скачать руководство пользователя страница 18

18

OPERATION

1. Move prime mover to a level surface with the blade properly attached.

2. Place the prime mover in “Park” and engage the parking brake.

3. Lower the blade onto the level surface.

4. Shut off prime mover engine, remove key and relieve all pressure from the hydraulic lines.

5. Check spring specifications on chart below.

RECOMMENDED SPRING SET-UP LENGTHS

Blade Width

60 in

72 in

84 in

96 in 108 in 120 in

Recommended Spring Set-up Length*

14.38 inches

Maximum Length Permitted- 15.33 inches

6. Test snow blade. If edges trip too easily, perform the following steps:

a. Repeat the above steps 1 through 4.

b. Tighten the spade (or eye) bolts to lengthen the springs.

WARNING! LENGTHENING THE SPRINGS BEYOND THE MAXIMUM

LENGTH PERMITTED CAN RESULT IN DAMAGE TO THIS

PRODUCT.

c. Test your blade again. If edges still trip too easily contact FFC.

*NOTE:

The Spring set-up lengths are measured from the inside of one hook to the inside of the

other hook. The relaxed length of the spring is 14 inches.

«
...
16
17
18
19
20
...
»

Содержание V-Snow Blade
















































Отзывы:

Нет отзывов