Festo EXCM-30 -PF Series Скачать руководство пользователя страница 65

Страница: 65 / 84

Diagnostics

Festo – EXCM-30/-40-...-PF-EN – 1603 – English

Hex

Type of error/diagnostic memory

Error name

Dec

Parameter file invalid

Can be parameterised as:

/-/-

Diagnostic memory: always

No valid parameter set stored.

The default parameter set is loaded automatically. Enter a valid parameter set in the device. If the

error is still present, the hardware may be defective.

– Acknowledgement option: Error can only be acknowledged after eliminating the cause.

Parameterisable error response(s):

Firmware update execution error

Can be parameterised as:

/-/-

Diagnostic memory: optional

The firmware update has not been properly executed/completed.

Check the Ethernet connection between the controller and PC and run the firmware update again.

The previous firmware version remains active until successful completion of the firmware update.

If this error is still present, the hardware may be defective.

– Acknowledgement option: Cannot be acknowledged, software reset required.

Parameterisable error response(s):

Overcurrent

Can be parameterised as:

/-/-

Diagnostic memory: always

Short circuit in the motor, lines or brake chopper. Output stage defective.

Incorrect parameterisation of the current regulator.

Check parameterisation of the current regulator. An incorrectly parameterised current regulator

can generate currents up to the short-circuit limit; as a rule this is clearly noticeable through high

frequency whistling.

If the error message occurs immediately when load voltage is applied:

short circuit in the output stage. The device must be replaced immediately.

If the error message does not occur until the drive is enabled:

– Disconnect the motor plug directly at the controller; if the error still occurs:

Replace controller.

– If the error only occurs when the motor cable is connected:

Check motor and cable for short circuits.

– Acknowledgement option: Cannot be acknowledged, software reset required.

Parameterisable error response(s):

t malfunction motor

Can be parameterised as:

/-/-

Diagnostic memory: always

The I²t limit for the motor is reached. The motor or the drive system may be insufficient for the re

quired task.

Check design of the drive system and mechanical system for sluggishness.

Reduce load/dynamics, longer breaks.

– Acknowledgement option: Error can be acknowledged.

Definable error response(s): B,

Содержание EXCM-30 -PF Series





















































































Результаты поиска

Содержание EXCM-30 -PF Series

Отзывы:

Похожие инструкции для EXCM-30 -PF Series

Бренды по названию

Популярные бренды

Festo EXCM-30 -PF Series, Руководство пользователя

Результаты поиска

Содержание EXCM-30 -PF Series

Отзывы:

Похожие инструкции для EXCM-30 -PF Series

Бренды по названию

Популярные бренды