Festo CPX-CMAX Скачать руководство пользователя

Страница: 79 / 98

Diagnostics and error handling

Festo – P.BE-CPX-CMAX-SYS-EN – en 2017-09b – English

Group 4 – System error A

CPX error group 104

(CPX-MMI: [System error A] )

No.

Reset type

Error level

Message

Teaching not possible

Note

Exact cause

Diagnostic memory or additional information in PNU 203.

Cause

Teaching (falling edge on CPOS.TEACH) is triggered unintentionally through

disconnection or switching off of the control.

Measure

Only activate CPOS.TEACH = 1 (prepare teaching) directly before the teaching

process. Always end teaching immediately.

Cause

Teaching not possible in direct mode.

Measure

Change operating mode.

Cause

Teaching not possible during active commissioning operation.

Measure

First end commissioning operation.

Cause

In the commissioning mode, the teaching target in parameter 1 is invalid.

Measure

Correct parameter 1.

Cause

Without reference, teaching is not possible.

Measure

Perform homing prior to teaching.

Cause

Lower software end position (SWEP) is greater than/equal to the upper SWEP

when teaching the SWEP in the commissioning mode. The SWEP is not adopted.

Measure

Teach upper SWEL first.

Correct the teach position.

Cause

Upper software end position (SWEP) is less than/equal to the lower SWEP when

teaching the SWEP in the commissioning mode. The SWEP is not adopted.

Measure

Teach lower SWEP first.

Correct the teach position.

Cause

Specified record number impermissible when teaching in record select mode.

Measure

Correct record number.

Cause

Parameterised control mode of the selected record when teaching in record

select mode is not permissible.

Measure

Correct control mode; correct record number.

Cause

Change of operating mode during active teaching process (CPOS.TEACH=1).

Measure

Do not change the operating mode during CPOS.TEACH=1.

Faulty commissioning function or parameter

Cause

Invalid function number when starting a commissioning operation in the

commissioning mode (

I/O data, commissioning mode - byte 3).

Measure

Correct the function number.

Cause

At least one parameter of the started commissioning operation had an invalid

value (

I/O data, commissioning mode - byte 4 ... 8).

Measure

Check and correct parameter 1 and parameter 2.

Cause

Movement test was started when a movement test has already been successfully

performed.

Measure

First reset movement test.

Содержание CPX-CMAX



































































































Результаты поиска

Содержание CPX-CMAX

Отзывы:

Похожие инструкции для CPX-CMAX

Бренды по названию

Популярные бренды

Festo CPX-CMAX, Описание

Результаты поиска

Содержание CPX-CMAX

Отзывы:

Похожие инструкции для CPX-CMAX

Бренды по названию

Популярные бренды