Festo CMMO-ST-C5-1-DION Скачать руководство пользователя страница 50

Страница: 50 / 174

Product description

Festo – GDCP-CMMO-ST-EA-SY-EN – 2017-05c – English

Target recognition

The characteristics when the target position are reached (target recognition) depends on the stroke

limitation.

Target recognition

Behaviour after target recognition:

… without stroke limitation

Speed is reached, i.e. the actu

al speed is inside the target

speed window for the duration

of the damping time.

The “Motion Complete” signal is set. The actuator continues to

move at target speed. Monitoring of the speed deviation remains

active. Force remains at the maximum value specified in the speed

record.

… With stroke limitation

–

Stroke limitation is reached

first

The “Stroke limitation” signal is set.

The actuator is braked down to a stop using the parameterised

Quick-Stop deceleration function. Although the target speed has

not yet been reached, the Motion Complete signal was set

(

Fig. 2.6 and Fig. 2.7)

Open-loop operation: the actuator remains at the target position

and is maintained in position with the predefined holding current.

Closed-loop operation: the actuator remains position-controlled.

–

Speed is reached first, i.e.

the actual speed is inside

the target speed window for

the duration of the damping

time.

The “Motion Complete” signal is set. The actuator continues to

move at target speed in closed-loop operation. Monitoring of the

speed deviation remains active; force remains limited to the max

imum stated in the order; stroke limitation remains enabled.

Tab. 2.45 Target recognition in velocity mode

Содержание CMMO-ST-C5-1-DION















































































































































































Результаты поиска

Содержание CMMO-ST-C5-1-DION

Отзывы:

Похожие инструкции для CMMO-ST-C5-1-DION

Бренды по названию

Популярные бренды

Festo CMMO-ST-C5-1-DION, Оригинальное руководство пользователя

Результаты поиска

Содержание CMMO-ST-C5-1-DION

Отзывы:

Похожие инструкции для CMMO-ST-C5-1-DION

Бренды по названию

Популярные бренды