Festo CMMO-ST-C5-1-DION Скачать руководство пользователя страница 43

Страница: 43 / 174

Product description

Festo – GDCP-CMMO-ST-EA-SY-EN – 2017-05c – English

2.5.4

Teaching

Teaching can be used to adopt the current position of the actuator for the following parameter set

tings:

Parameter

Teaching by …

Target position of the record currently selected

I/O interface, FCT, web server

Axis zero point

FCT

Position comparator limits

FCT

Project zero point

FCT

Software end positions

FCT

Record type “Positioning to absolute position”

Tab. 2.36 Teaching in positions

The drive must not stand still for teaching. However, even at low speeds, inaccuracies of several milli

metres are possible, due to the usual cycle times of the motor controller and the higher-order control

ler. The speed must be set during teaching in such a way that the position is detected accurately

enough.

The Teach process always runs in the following steps:

1. The parameter

Tab. 2.36 is selected and/or addressed.

2. The actuator is moved into the desired position (e.g through jogging

Section 2.5.3).

3. A teach command is triggered to adopt the current position.

Teaching with FCT or web server

The taught position is displayed after successful teaching in the software. Parameterisation in the

controller becomes effective through download. Additional information:

–

Teaching with web server

Chapter 5.3.5

–

Teaching with FCT

PlugIn aid for FCT

Teaching via I/O interface (binary profile)

The number of teachable target positions is limited to 7 sets of commands. The Teach process is per

formed with a handshake process using signals TEACH/ ACK. The taught position is displayed in the

controller immediately after successful teaching. The position is saved permanently using the “Auto

matic saving” option. If this option is not set, permanent saving via FCT or web server is possible.

Other information

Chapter 5.6.7

Содержание CMMO-ST-C5-1-DION















































































































































































Результаты поиска

Содержание CMMO-ST-C5-1-DION

Отзывы:

Похожие инструкции для CMMO-ST-C5-1-DION

Бренды по названию

Популярные бренды

Festo CMMO-ST-C5-1-DION, Оригинальное руководство пользователя

Результаты поиска

Содержание CMMO-ST-C5-1-DION

Отзывы:

Похожие инструкции для CMMO-ST-C5-1-DION

Бренды по названию

Популярные бренды