Festo CMMO-ST-C5-1-DION Скачать руководство пользователя страница 171

Страница: 171 / 174

Control via Ethernet (CVE)

Festo – GDCP-CMMO-ST-EA-SY-EN – 2017-05c – English

171

#218

Unit of measurement conversion factor

Drive functions

UINT08

R/W1/-/-/-

Example in section B.2

0: Undefined

1: Metre

2: Inch

3: Revolutions

4: Degree

Values: 0 … 4

Default: 0

#295

Current target position

Drive functions

SINT32

R/-/-/-/-

Target position of the currently executed drive function.

The target position is calculated according to the definition as follows:

– Position record: absolute target position

– Reference travel with movement to zero: target position = 0

– Reference travel without movement to zero: target position = (–1) * axis zero point

– Jog positive: positive software end position, if this is activated, otherwise 2

–1

– Jog negative: negative software end position, if this is activated, otherwise –2

– Speed & force record: Absolute position specified through the stroke limit (braking begins at the

stroke limit). If the stroke limit is deactivated, target position is calculated from the software limit

positions.

For record linking, the target position of the current positioning record is always relevant.

Unit: SINC

Values: –2147483648 … 2147483647

Default: 0

#358

Unit of measurement conversion factor

System

UINT08

R/-/-/-/-

Bit field for the Enable status (e.g. STO)

Bit 0: STO

Bits 1 … 7: reserved

Only if all bits are 1 can the finite state machine be switched to the status “Operation enabled”

through the control word.

Unit: Bit field

Values: 0 … 255 Default: 254

Содержание CMMO-ST-C5-1-DION















































































































































































Результаты поиска

Содержание CMMO-ST-C5-1-DION

Отзывы:

Бренды по названию

Популярные бренды

Festo CMMO-ST-C5-1-DION, Оригинальное руководство пользователя

Результаты поиска

Содержание CMMO-ST-C5-1-DION

Отзывы:

Бренды по названию

Популярные бренды