Ferplast Swing, Руководство пользователя

Страница: 11 / 40

have already been drilled when the panes are
manufactured.
6a Measure the belly height of your pet from the floor and position the
template (side A) on the door with the bottom at the same height.
Mark the bottom side using a marker, you will use it as the base to
center the compasses on the points marked on the template.
Then follow these instructions:
6b drill a circular hole with radius of 108 mm if your pet flap is SWING
5, of 105 mm if it is SWING 7 MAGNETIC (The centre of the hole is
marked on the template). 13a
6c drill four circular holes in the four corners of the pet flap, if it is
SWING 9, SWING 11 or SWING 15. Then cut the tangents of the 4
holes to obtain a unique opening on the glass. (The centre of the
holes are marked on the template). 13b/c/d
The biggest job is done. Go to paragraph "Cut the tunnel"
Metal doors (7a)
Follow the same instructions as those for wooden doors. The only
difference lies in the fact that the SWING 7 MAGNETIC needs to
be isolated in metal doors for the key to be able to work. It is to be
isolated using a non-metal material (wood or similar), which must
have a minimum thickness of 40 mm around the entire perimeter. This
prevents any interference and ensures the correct operational efficiency
of the magnetic mechanism. The biggest job is done. Go to paragraph
"Cut the tunnel"
Walls (7b)
Follow the same instructions as those for wooden doors. (Jobs 5b, 5c
and 5d are to be done using suitable tools). The tunnel supplied can be
installed in walls with a thickness of more than 55 mm. In this case the
tunnel must be extended in cement plastering. The biggest job is done.
Cut the tunnel (8)
Warning!
Do not cut the tunnel of the SWING 7
MAGNETIC because it contains delicate mechanism!
Cut the tunnel to the required length, this only takes a few minutes and
will hide all the uneven edges.
8a Measure depth “Y” of the support (door or wall) on which the pet
flap is to be installed.
8b Mark a line along the outer surface of the tunnel at a distance “Y”
plus 8 mm. You can use the template (side B) that has been printed
with the 4 most common installations sizes (Tab 1) where “N”
indicates the slit to be used to mark the line and “Y” indicates the
thickness of the support on which the pet flap is to be installed.
Place the template on the tunnel and mark a line by the slit relative
to the required installation size.
8c Repeat the marking of a line on the other sides of the tunnel.
8d Cut the tunnel using a jig saw, starting from one of
the corners and continuing along the perimeter. Do
not cut two sides next to each other or parallel at the
same time to avoid moving away from the references.
Warning!
The tunnel supplied is suitable for
installations from 0 to 55 mm in thickness. The
outer surface has one or a number of grooves,
depending on which version, positioned to
match those of the most used installation sizes.
The purpose of these is to make it easier to cut
the tunnel. Before cutting along these grooves,
ensure that the size of the tunnel you are about
to cut is compatible with your wooden, glass, or
walls thickness.
8e The 4-way locking system is to be fitted on the inner side of the
door. Position the flap on the hole and using a marker, mark the
positions where the screws are required.
8f Remove the flap and drill 4 holes using a drill with a 4.5 mm bit.
Fit the pet flap (9)
9a Fit the flap and secure it with the screws supplied, which may
have to be cut and filed to remove any sharp edges. 4 short screws
are supplied for fitting to glass doors and fly screens and 4 long
screws for all other installations on a thickness of up to 55 mm.
The 4 long screws will have to be shortened for installations on an
intermediary thickness (i.e.: for installations on a thickness of 45
mm shorten the screws by 10 mm; for installations on a thickness
of 35 mm shorten the screws by 20 mm, and so on). Instead, you
could purchase a new set of screws to your specifications at your
local hardware store. Too short a screw could strip the thread
whereas too long a screw could break the front panel of the pet
door.
9b To finish the job, cover the screw holes using the plugs supplied,
making sure to match the rib to the seat.
YOUR SWING PET FLAP IS NOW READY TO USE!
A quick test for the magnetic key (4)
If you have purchased the SWING 7 MAGNETIC model we advise you to
carry out this quick test to make sure it works.
4a From outdoors, ensure that the four-way locking system is in the
“access and exit” position. Holding the magnetic key in front of
you, with the name Ferplast at the bottom and the arrow pointing
towards the flap. The cat flap mechanism should trigger at roughly
10 cm from the flap.
4b Secure the magnetic key to the collar with the arrow facing your
pet’s head (4b). Do not hang anything else but the magnetic key
on the collar to avoid interference with the opening system. Ensure
that the collar is neither too tight nor too loose (you should be able
to slip the collar off your pet). The magnetic key should ideally hang
so that the bottom part is just above the bottom edge of the tunnel
when the cat approaches the pet flap (4c). If the magnet is not at
a distance from the bottom edge of the tunnel of between 0-4 cm
(0-1,5”), the cat could have difficulty in triggering the opening
mechanism (4d-4e).
Manual mode (10)
If you do not wish to use the magnetic system, the cat flap can
be converted to work manually. To do so, turn the cut-out screw
situated on bottom edge of the tunnel by 180°, from the DX position
(mechanism enabled) to the SX position (mechanism disabled) as
illustrated.
Important!
This procedure is extremely
useful if your pet should loose the magnet.
Cleaning: effective, quick and easy
This pet flap is made of remarkable high quality plastic. The flap
is reinforced and has been designed to last with time. To keep it in
working order simply clean it now and again with a damp cloth.
Spare parts (11)
The flap has been designed to allow every single damaged part to be
replaced. In particular, the pivoting flap can be replaced taking away
the screws of the rear part in the main door (11a). When placing a spare
flap in SWING 11 and 15 models make sure that springs are correctly
fitted in the hinges (11b).
Our after sales service.
In the rare case of accidental breakage, we are pleased to offer you our
wide range of spare parts for the pet flap you have purchased. Please
contact your local Ferplast dealer.
WARRANTY.
This product all its parts and accessories are covered by
warranty within the limits provided for in this paragraph and the legal
regulations currently in force. The guarantee only covers manufacturing
defects and includes the repair or replacement of the product free of
charge. The guarantee does not cover damage and/or defects caused by
carelessness, wear, unsuitable usage not complying with the instructions
and warnings in this manual, accidents, tampering, incorrect use, bad
repair work or purchases not accompanied by a fiscal receipt.
GB
PL
DA
SV
HU
CS
SK
PT
ES
NL
DE
FR
IT
RU