Fenix Imvico SM3000 Скачать руководство пользователя страница 36

Страница: 36 / 55

FENIX IMVICO

SM3000 OPERATION MANUAL

[Notes]

•

This command is effective only processed at the beginning of the line.

•

If the setting exceeds the printable area, the maximum value of the printable area is used.

•

The horizontal motion unit (

) is used for calculating the left margin. The calculated result

is truncated to the minimum value of the mechanical pitch.
[Default]

= 0,

= 0

nH d1...dn

[Name]

Print a 2D AZTEC format bar code

[Format]

ASCII

d1..dn

Hex

d1..dn

Decimal

d1..dn

[Description]

Prints a 2D Aztec bar code with n characters where n =

x 256.

[Range]

= <00>H, <00>H

≤

<FF>H.

The maximum number of characters is undetermined as it depends on the available

paper size and the type of characters to be printed (numbers, uppercase / lowercase

characters, etc.)

[Example]

Sending the following command to the printer will result in a 2Daztec bar code as shown
below.
<1D 50 2D 00> H <ABC 123456789. This is an AZTEC bar code test>ASCII

nH d1...dn

[Name]

Print a 2D QR format bar code

[Format]

ASCII

d1..dn

Hex

d1..dn

Decimal

d1..dn

[Description]

Prints a 2D QR bar code with n characters where n =

x 256.

Regardless of the

amount of data to encode, always the QR code is printed on 7M format (45x45).

[Range]

= <00>H, <00>H

≤

<FF>H.

The maximum number of characters is undetermined as it depends on the available

paper size and the type of characters to be printed (numbers, uppercase / lowercase

characters, etc.)

[Example]

Sending the following command to the printer will result in a 2D QR bar code as shown

below.

<1D 51 2D 00> H <ABC 123456789. This is an QR bar code test>ASCII

36/55

Left margin

Printing area width

Printable area

Содержание SM3000
























































Результаты поиска

Содержание SM3000

Отзывы:

Бренды по названию

Популярные бренды

Fenix Imvico SM3000, Руководство по эксплуатации

Результаты поиска

Содержание SM3000

Отзывы:

Бренды по названию

Популярные бренды