Fenix Imvico SM3000 страница 35 Скачать руководство пользователя

Страница: 35 / 55

FENIX IMVICO

SM3000 OPERATION MANUAL

GS H

[Name]

Select printing position for HRI characters

[Format]

ASCII

Hex

Decimal

[Range]

= 0/3

[Description]

Selects the printing position of HRI characters when printing a bar code.

selects the printing position as follows:

Printing position

Not printed

Above the bar code

Below the bar code

Both above and below the code bar

[Notes]

•

HRI indicates Human Readable Interpretation.

•

HRI characters are printed using the font specified by

GS f

[Default]

= 0

[Reference]

GS f

GS k

[Name]

Firmware version transmission

[Format]

ASCII

Hex

Decimal

[Range]

= <33>H

[Description]

● Transmits the firmware version number.
● Besides of checking the firmware version by printing the self-test page, this command

can be used as support for possible automatic firmware upgrade through the host
application. Thus, the system could check whether the current version is less than the
new provided (contact with FENIX IMVICO or distributor if necessary).

● Returns one byte indicating numerically the current firmware version and revision (1

and 2

index. 3

index indicates the boot firmware version and it is not transmitted by

this command
Example:

GS L

nL nH

[Name]

Set left margin

[Format]

ASCII

Hex

Decimal

[Range]

≤

255

≤

255

[Description]

Sets the left margin using

and

•

The left margin is set to [(

x 256) x

0.125 mm)].

35/55

FENIX IMVICO
SM3000 V1.0.1

SERIAL PORT
SETTINGS

Data bits:

8 (fixed)

Stop bits:

1 (fixed)

Baud rate: 115200 bauds

Byte transmitted: 10

Содержание SM3000
























































Результаты поиска

Содержание SM3000

Отзывы:

Похожие инструкции для SM3000

Бренды по названию

Популярные бренды

Fenix Imvico SM3000, Руководство по эксплуатации

Результаты поиска

Содержание SM3000

Отзывы:

Похожие инструкции для SM3000

Бренды по названию

Популярные бренды