EN
10
To move the machine while it is still inside the packing, use
a fork lift by inserting the two forks in the rooms provided
under the bearing board
Move the machine carefully and avoid sudden movements
which could unbalance the load and make it drop.
To remove the machine from the plate after packing removal,
loosen the fi xing screws but keep them should the machine
be transported for long stretches.
To transport the machine after freeing it from the plate,secure
it with resistant chains, ropes or braces, by passingthem
through the the eyebolts provided.
Then the machine must be lifted using a hoist of adequate
capacity or through another means suitable for this
purpose.
WARNING: Do not lift the machine by the body D
(Fig. 1).
WARNING: Before lifting the machine, check that
the body is lowered and secured to the rest of
the structure by means of ropes or other claming
means as shown in Fig. 2
2.3
ELECTRICAL CONNECTIONS (Fig. 3)
Check that the mains to which the machine is connected is
earthed in accordance with current safety regulations and
that the power point is in good condition.
Remember that there should be a magnetothermic
protective device fi tted upstream of the mains to protect all
the conductors from short circuits and overloads.
This protective device should be selected according to the
electrical features of the machine stated on the motor.
In case of power failure in mains, while you wait for power
to be restored there is no danger hazard may arise: in
fact, the main switch
D (Fig. 3)
is also equipped with a
reset function which prevents the machine from restarting
automatically.
The motor of your sawing machine is equipped with a
protective heat circuit breaker which interrupts the power
supply when the temperature of the coils rises too high.
When the power supply is interrupted, wait for normal
reset.
2.4
POSITION/WORK STATION (Fig. 5)
Position the machine by moving it as described in
paragraph 2.2 on to a suffi ciently level bench, in such a
way that the coolant can refl ow in the collecting tank during
the cutting operations.
Taking the ergonomic criteria into consideration, the ideal
height shall be that which enables you to position the
table between 90 and 95 centimetres from the fl oor
(see
Fig. 2)
.
Now, cut the strap which holds the body lowered and
remove the wooden cap which protects the machine
while in transit.
CAUTION: Make sure that the machine is placed
in a working area with suitable environmental
conditions and lighting. The general conditions
of the working environment are of fundamental
importance for accident prevention.
Now lift the machine body and fi t the eye of spring A into
its location on pin B to prevent the spring from being
expelled.
3 ADJUSTING
3.1
TENSION OF THE BLADE (Fig. 4)
Turn the handwheel clockwise
B
till the green indicator
lights
C
up.
WARNING: The tensioning device is equipped
with a safety microswitch which prevents the
machine from operating till the blade is tensioned
correctly.
3.2
BAR STOP (OPTIONAL) (Fig. 6)
Use the bar stop supplied if you have to do several cuts on
pieces of the same length.
In this way you do not have to repeat the same
measurement each time.
Before adjust the bar stop, be sure the main switch
B
(Fig.
7)
is in 0 position.
Screw rod
A
into the hole of the vice and fasten it with nut
B
Slacken the handwheel
C
and place the stop
D
at the correct
distance from the blade. Tighten handwheel
C
again.
3.3
CUTTING ANGLE (Fig. 7)
The machine can effect cuts ranging from 0° to 60°.
To unlock the body rotation, release the handle
A
on the
rotating support.
Rotate the machine body to the left up to the stop which is
set to 60° by the manufacturer.
To have the stop set to 45°, loosen the handwheel
E
, pull
the bracket
D
till the end of stroke corresponding to the
end of the slot of the bracket and re-lock the handwheel
E
. Now, when the machine body is turned to the left, the
stop is automatically at 45°.
To restore the stop at 60°, proceed as above described and
re-position the bracket
D
to its original position.
For all other inclinations, match the mark
C
of the rotating
support and the corresponding position on the plate
B
.
3.4
CUTTING SPEED (Fig. 8-3)
Depending on the type of material and its section (see
CUTTING TABLE) you can choose two different cutting
speed 60 or 80 m/min. by means of the switch
N
.
2200_PARTI COMUNI.indd 10
2200_PARTI COMUNI.indd 10
21/10/2008 15.27.42
21/10/2008 15.27.42
