Federal Signal Corporation ultravoice UV Скачать руководство пользователя страница 34

Страница: 34 / 79

Installation

UltraVoice (UV)

Electrical Connections

Install the siren electrical system in compliance with local electrical codes

and NEC recommendations. Federal Signal also recommends that all user-

installed conduit connections enter from the bottom of the cabinet. Disconnect

all power and read all warnings at the beginning of this manual and on the

batteries before making connections.

The UV controller must be solidly connected to an earth ground. If the siren

is installed in a building, ground the system to a metallic object known to be

grounded. For pole mount installations, drive a metal rod or bar at least 8 feet

into the ground, as close as practical to the base of the pole. Use a separate,

continuous 6 AWG or larger wire from the siren frame to ground and from the

cabinet of each siren control system to ground.

NOTE

: Seal and protect conduit connections to prevent water entry and corrosion in the

Control Cabinet.

Power Connections

To connect the wires in the Control Cabinet, do the following:
1. Route 1/2 inch conduit (steel preferred) between the user-supplied, fused

disconnect switch and the conduit-fitting hole in the bottom right-hand of the

Control Cabinet enclosure. Use weatherproof switches, electrical boxes and

connectors to prevent water entry and corrosion.

2. Route two user-supplied power wires and a ground wire through the conduit that

was just installed between the Control Cabinet and the fuse disconnect box. Use

wires no smaller than 14 AWG.

3. Connect the ground wire to the green and yellow DIN mounted terminal block

or the cabinet ground stud. Verify the appropriate siren model was purchased.

240 Vac models contain a step-down transformer pre-wired to the DIN rail

located on the right side of the Control Cabinet.

4. Connect the two ac power wires to the DIN mounted terminal blocks labeled L1

and L2.

5. Connect the power wires and the lightning protector to the ac disconnect box per

instructions provided with the lightning protector and governing electrical codes.

Содержание ultravoice UV















































































Результаты поиска

Содержание ultravoice UV

Отзывы:

Похожие инструкции для ultravoice UV

Бренды по названию

Популярные бренды

Federal Signal Corporation ultravoice UV, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ultravoice UV

Отзывы:

Похожие инструкции для ultravoice UV

Бренды по названию

Популярные бренды