FARMTECH FDD 3000 Скачать руководство пользователя страница 81

Страница: 81 / 105

C.10.1 Operating

On/Off Button

Settings Button

You can start the device by pressing the on/off button (1)
for once after making the necessary device connections.
The device will immediately start

with the

last

configured settings

Work display shows two main information columns.

1. Speed:

is shown in (km/h) kilometer/hour unit

2. Seeded area

: is shown in (m

) square meter unit.

WARNING:

Intermittent “SYSTEM IS IN STANDBY

MODE” warning is shown on the information display
when tractor and grain drill are stationary.

Note:

In order to run this

device, tractor’s ignition key

must be in parking position and the 12V igniter inlet must
be usable.

C.10.2 Settings

The device settings are adjusted with the

settings

button

(11) on the control display. Next setting is

displayed each time the button is pressed. The
diagram of the settings menu that is accessed in this
way is given below:

Содержание FDD 3000










































































































Результаты поиска

Содержание FDD 3000

Отзывы:

Бренды по названию

Популярные бренды

FARMTECH FDD 3000, Руководство пользователя

Результаты поиска

Содержание FDD 3000

Отзывы:

Бренды по названию

Популярные бренды