FARMTECH FDD 3000 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 105

FARMTECH FDD 3000 Скачать руководство пользователя страница 16

18.

Extra weights attached to machine and tractor adversely affect the maneuver and

braking capability of tractor. Use tractor more carefully and slowly since this situation
will reduce the driving safety.

19.

Be careful when turning. The weight, width and centrifugal force of the equipment

engaged to tractor may take tractor out of control. There must be no one within the
turning and drifting area of machine.

20.

No one must stand in the vicinity of hydraulically opening and closing frames during

operation.

21.

Do not contact with moving parts even for instant interventions when machine is

moving. Do not insert your hand in seed and fertilizer box.

22.

Check hydraulic hoses frequently; replace in case of wear or tear. Only use hoses

with specifications recommended by the manufacturer. Use protective equipment
(mask, safety goggles, protective clothes, etc.) when inspecting hydraulic system
leakages since there is injury hazard. High-pressure liquids (hydraulic oil) cause
severe injury by penetrating into the skin! Seek medical care in such a case.

23.

Note that in case of reverse connection of hydraulic connections, functions will

be reversed, too. (

Accident hazard!)

Lower the machine on the ground if you are

going to do work on hydraulic unit. Reduce the pressure by draining the oil inside the
unit and stop tractor.

24.

The hydraulic system on tractor has high pressure. When connecting hydraulic hoses

to the hydraulic system of tractor, make sure that the system in both directions is not
under pressure.

25.

Lower machine and coulter before leaving tractor after transport and operation. Stop

the engine. Remove the ignition key.

26.

Special knowledge and equipment is necessary for the mounting of wheels.

Therefore, it is appropriate that wheels are repaired by specialists. Tire pressures must
be checked periodically and air pumped, if necessary.

27.

Double disk grain drills are designed to operate by moving on a

straight line and “

in

forward direction

” only. Hence,

it cannot move backwards or turn to the right or left

when coulter is contacting with the ground

. When turning during cushioning, coulter is

lifted and then turning is done. If it is impossible, turning is done by using the widest curve
possible.

28.

Any modification and repair made on machine by authorized persons will make the

warranty of machine void. Also, all material damages and liabilities to arise from such
procedure shall belong to the product owner.

«
...
14
15
16
17
18
...
»

Содержание FDD 3000










































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды