FARMTECH FDD 3000 Скачать руководство пользователя страница 74

Страница: 74 / 105

C.7 Harrow Adjustments

1. Hardness adjustment plate

2. Harrow Spring

3. Harrow Block

4. Harrow Height Adjustment Slots

5. Harrow Bar

6. Limiting Pin

7. Counter Slot

8. Frame Connecting Slot

C.7.1. Active and Passive Positions of Covering

Harrows

The harrows on the coulters can be disabled by
switching to passive position when necessary. The
harrows are switched to passive positions by
following the steps below:

1. Step:

Remove the limiting pin (6) and the R pin on

top of it.

2. Step:

Rotate the harrow bar (5) so that it ends come

to the front by 180 degrees.

3. Step:

Remount the limiting pin (6) and the R pin on

top of it.

4. Step:

Apply the 3 procedure steps listed

above for all the harrows.

Active Position of Covering

Harrows

Passive Position of Covering

Harrows

Содержание FDD 3000










































































































Результаты поиска

Содержание FDD 3000

Отзывы:

Бренды по названию

Популярные бренды

FARMTECH FDD 3000, Руководство пользователя

Результаты поиска

Содержание FDD 3000

Отзывы:

Бренды по названию

Популярные бренды