Famed SU-02 Скачать руководство пользователя страница 15

Operating Manual for Operating Table SU-02.0

_____________________________________________________________________________________________________

Caution!

When the anti-trendelenburg function is performed, the footrests may collide with 
the base!

3.7 Change of angular position of divided footrests 

In order to change the angular position of divided footrest one should unscrew knob 1 or 2 (depending 
on which of the footrest parts you want to adjust) till the toothed bars are out of mesh. The footrest 
should be positioned in the required position and the adjusting toothed bar should be locked by turning 
of knob 1 or 2. 

Fig. 7

Caution!

When  one   locks   a  set  position  of  the   footrest,  one   should  make   sure   that  the 
toothed bar is correctly meshed.

3.8 Rotation of the footrest

In order to put the footrests apart, the knob  (drawing 1-3 item 21)  shall be turned anticlockwise, that  
causes toothed bar separation by a few mm and in that way the foot segment may be rotated around 
vertical axis within the range provided in technical data. In order to lock the footrest the knob shall be 
turned again but this time clockwise, then toothed bar will mesh and footrest movement will be locked. 

Caution!

Toothed bars must be correctly meshed! When the knob is being turned down, 
one should check if the toothed bars are meshed.

3.9 Installation and removal of the footrest

The footrest may be placed and removed from the seat segment thanks to the mechanism which is 
moved by the lever (drawing 1-3 item 22). In order to remove the footrest segment one should hold the  
segment by its bottom, pull the lever towards the segment (drawing 1-3 item 22) and take the segment 
out of the hole in the seat segment. The footrest segment is installed by placement of the mandrel of  
the segment in the opening in the seat segment and simultaneous pulling back of the lever. When the  
segment  is  installed  one  should  release  the  lever  which  thanks  to  a  spring  will  get  into   its  initial 
position.  

Caution!

The segment should be held before the lever is released!
Make sure that the lever is in the right position!

3.10 Installation and operation of the headrest

The headrest is fastened on installation wedges which are situated at the end of the backrest segment 
using a knob. When the headrest is put on the stripe, one should determine its position by screwing  
down the screw (drawing 1-3 item 12). The headrest is dismounted by unscrewing of the screw and 
removal of the headrest from the stripe. The angle of the headrest is changed similarly to the backrest  

_________________________________________________________________________________

page 15

Содержание SU-02





























Отзывы: