Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 135

background image

Network OS identifies fan assemblies from left to right as fan #1, fan #2, fan #3, fan #4, and fan #5 when viewed from the non-port
side of the device. For locations of these assemblies, captive screws, LEDs, labels, and other components, refer to the non-port side view
of the VDX 6740T in

Hardware components

NOTE

Maintain all power supply and fan assemblies in operational condition to provide redundancy.

CAUTION
Because the cooling system relies on pressurized air, do not leave any of the power supply and fan assembly slots empty
longer than two minutes while the switch is operating. If a power supply orand fan assembly fails, leave it in the switch until
it can be replaced.

CAUTION
Disassembling any part of the power supply and fan assembly voids the warranty and regulatory certifications. There are no
user-serviceable parts inside the power supply and fan assembly.

DANGER

The procedures in this manual are for qualified service personnel.

Refer to details on the meaning of LED patterns for the VDX 6740T power supplies and fans in

on page 101 to verify

operation and determine if replacement is necessary.

Determining the need to replace a power supply

Use one of the following methods to determine the status of the power supplies:

•

Check the power supply status LEDs. Refer to "Interpreting LED activity" for details on LED normal operation and error
conditions.

•

Enter one of the following commands in the command line interface to display power supply status:
–

show chassis

–

show environment power

•

Check the power supply status in the Web Tools application.

Time and items required to replace a power supply

Replacing a power supply should take less than two minutes to complete.

You need the following items to replace a power supply:

•

A new power supply (must have the same part number and the same airflow label as the power supply being replaced)

•

A #2 Phillips-head screwdriver

Replacing a 500W AC power supply

Complete the following steps to replace a 500W AC power supply.

NOTE

Before beginning the replacement, refer to the precautions in "Power precautions."

1. If leaving the device in service while replacing a power supply, verify that the other power supply (the one not being replaced)

has been powered on for at least four seconds and has a steady green status LED.

FRU replacement in the VDX 6740T

ExtremeSwitching VDX 6740 Hardware Installation Guide

9036108-00

113

«
...
111
112
113
114
115
...
»

Содержание ExtremeSwitching VDX 6740








































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching VDX 6740

Бренд: KE2 Страницы: 4

Бренд: IDEC Страницы: 8

Бренд: IDEM SAFETY SWITCHES Страницы: 2

Бренд: Field Controls Страницы: 4

Бренд: Ableconn Страницы: 16

Бренд: Lantech Страницы: 118

Бренд: 3onedata Страницы: 2

AMX ENOVA DVX-3250HD-SP

Бренд: Harman Страницы: 119

Бренд: cable matters Страницы: 12

Бренд: Origin Instruments Страницы: 6

Бренд: Planet Страницы: 2

Бренд: Labgear Страницы: 8

Бренд: National Instruments Страницы: 12

Бренд: Comm-Tec Страницы: 10

Бренд: Leaksafe Solutions Страницы: 12

Бренд: Eneo Страницы: 19

Бренд: Lindy Страницы: 6

Бренд: HB Products Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды