Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 123

Страница: 123 / 135

Regulatory compliance (safety)

•

CAN/CSA-C22.2 No. 60950/UL 60950

•

EN 60825 Safety of Laser Products

•

EN 60950/IEC 60950 Safety of Information Technology Equipment

Regulatory compliance (environmental)

•

2011/65/EU - Restriction of the use of certain hazardous substance in electrical and electronic equipment (EU RoHS).

•

2012/19/EU - Waste electrical and electronic equipment (EU WEEE).

•

94/62/EC - packaging and packaging waste (EU).

•

2006/66/EC - batteries and accumulators and waste batteries and accumulators (EU battery directive).

•

1907/2006 of the European Parliament and of the Council of 18 December 2006 concerning the Registration, Evaluation,
Authorisation and Restriction of Chemicals (EU REACH).

•

Section 1502 of the Dodd-Frank Wall Street Reform and Consumer Protection Act of 2010 - U.S. Conflict Minerals.

•

30/2011/TT-BCT - Vietnam circular.

•

SJ/T 11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in EIPs (China).

•

SJ/T 11364-2006 Marking for the Control of Pollution Caused by EIPs (China).

ExtremeSwitching VDX 6740 Switch Technical Specifications

ExtremeSwitching VDX 6740 Hardware Installation Guide

9036108-00

123

Содержание ExtremeSwitching VDX 6740








































































































































Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching VDX 6740, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды