Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 102

Страница: 102 / 135

TABLE 3

Port side LED patterns during normal operation (continued)

LED name

LED color

Status of hardware

Recommended action

Ethernet ports in either 10 GbE or
1 GbE mode (one green LED per
port)

Off (no light)

Port is shut, no link, or no license is
available for this port.

Enable the port.

Steady amber

Protocol down or no sync.

Check the local port SFP+ or QSFP
or peer port SFP+ or QSFP and
cable.

Slow blinking amber

Port is shut or chassis disabled or
POST failed.

Enable the port.

Fast blinking amber

Port has faulted and goes into shut
state.

Check messages for fault reason
and take necessary action.

Steady green

Link is present, no activity.

No action required.

Slow blinking green

Port is good except ISL is
segmented.

No action required.

Fast blinking green

Beaconing enabled.

No action required.

Flickering green

Online, frames flowing through the
port.

No action required.

40 GbE Ethernet ports (QSFP) in
40 GbE mode(one bicolor LED
[green and amber] per port)

Off (no light)

Port is no shut and no QSFP is
inserted or 40G port on demand
(POD) license not installed.

Connect media and cable or install
POD license.

Steady green

Link is present, no activity.

No action required.

Blinking green

Beaconing enabled, online with
frames flowing through the port.

No action required.

Steady amber

QSFP is inserted but no fiber or link
detected.

Insert cable or check cable on peer
40 GbE port.

Flashing amber

Port is shut or chassis disabled or
POST failed

Check messages.

40 GbE Ethernet ports (QSFP) in
4x10 GbE breakout mode (one
bicolor LED [green and amber] per
40 GbE port)

Off (no light)

All of the enabled ports (no shut)
have no media or cable or one, two,
or three ports are shut. The 40G
port on demand (POD) license not
installed.

Connect media and cable or install
POD license.

Steady green

All no shut ports are online. Any
unused ports must be shut.

No action required.

Blinking green

Beaconing enabled, online with
frames flowing through the port.

No action required.

Steady amber

Some no shut ports are not
connected.

Ensure that any unconnected ports
are shut.

Flashing amber

All four breakout ports are shut or
chassis is disabled or POST failed.

Check messages.

The following table describes the LEDs on the non-port side of the device..

TABLE 4

Non-port-side LED patterns during normal operation

LED name

LED color

Status of hardware

Recommended action

Power supply and fan assembly
status (one LED [green] per power
supply and fan assembly)VDX
6740

Off (no light)

Assembly is not receiving power or
is turned off.

Verify the assembly is on and
seated and the power cord is
connected to a functioning power
source.

Steady green

Assembly is operating normally.

No action required.

LED activity interpretation

ExtremeSwitching VDX 6740 Hardware Installation Guide

102

9036108-00

Содержание ExtremeSwitching VDX 6740








































































































































Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching VDX 6740, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды