Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 135

background image

NOTE

Rack mount kits described in this document are those supported at the time of publication. For the latest support information,
contact your Extreme Networks representative.

Mounting precautions

The following precautions specifically apply to mounting the device.

DANGER

Use safe lifting practices when moving the product.

DANGER

Mount the devices you install in a rack as low as possible. Place the heaviest device at the bottom and progressively place
lighter devices above.

CAUTION
Make sure the airflow around the front, and back of the device is not
restricted.

CAUTION
Use the screws specified in the procedure. Using longer screws can damage the
device.

CAUTION
To prevent damage to the chassis and components, never attempt to lift the chassis using the fan or power supply handles.
These handles were not designed to support the weight of the chassis.

Refer to the "EIA rack considerations" in

Installation and safety considerations

Standalone installation

Complete the following steps to install the device as a standalone unit on a table top.

1. Unpack the device and verify the items listed under "Items included with this device" are present and undamaged.
2. Apply the adhesive rubber feet to the device. The rubber feet help prevent the device from sliding off the supporting surface.

a)

Clean the indentations at each corner of the bottom of the device to ensure that they are free of dust or other debris that
might lessen the adhesion of the feet.

b) With the adhesive side against the chassis, place one rubber foot in each indentation and press into place.

3. Place the device on a flat, sturdy surface.
4. Provide power to the device as described under "Providing power to the device."

NOTE

Do not connect the device to the network until the IP address is correctly set. For instructions on how to set the IP
address, refer to "Configuring the device IP address."

Mounting precautions

ExtremeSwitching VDX 6740 Hardware Installation Guide

30

9036108-00

«
...
28
29
30
31
32
...
»

Содержание ExtremeSwitching VDX 6740








































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching VDX 6740

SmartPro DGS-1500-20

Бренд: D-Link Страницы: 113

xStack DGS-3120 Series

Бренд: D-Link Страницы: 1150

Бренд: Qlogic Страницы: 135

SANbox2 SANbox2-64

Бренд: Qlogic Страницы: 224

Бренд: Field Controls Страницы: 4

Бренд: VeEX Страницы: 22

SEHI SEHI100TX-

Бренд: Cabletron Systems Страницы: 75

Бренд: Comtech EF Data Страницы: 70

USB 2.0 7-Port Hub HO97916

Бренд: GE Страницы: 19

Бренд: WTI Страницы: 56

Бренд: Omega Страницы: 17

Бренд: Black Box Страницы: 2

Бренд: Eneo Страницы: 19

CTRLink EISK8P-GT

Бренд: Contemporary Controls Страницы: 4

Clear Switch CF-POE8

Бренд: ANTIFERENCE Страницы: 7

Бренд: IBM Страницы: 2

Бренд: Shure Страницы: 3

Бренд: JDS Uniphase Страницы: 113

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды