Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 116

Страница: 116 / 135

4. Install the new fan assembly in the chassis:

Orient the new fan assembly with the captive screw on the right, as shown in the following illustration.

b) Gently push the fan assembly into the chassis until it is firmly seated.

CAUTION
Do not force the installation. If the power supply and fan assembly does not slide in easily, ensure that it is
correctly oriented before continuing.

If the device is powered up, the fan will immediately power up.

Using the Phillips screwdriver, secure the fan assembly to the chassis by tightening the captive screw.

FIGURE 73

Inserting the fan assembly

5. Verify that the fan status LED is steady green to indicate normal operation.

If the LED is not steady green, ensure that the fan is securely installed and seated properly.

You can enter one of the following commands at the command line prompt to display fan status:
•

show chassis

•

show environment fan

The fan status can also be viewed using the Web Tools application.

FRU replacement in the VDX 6740T

ExtremeSwitching VDX 6740 Hardware Installation Guide

116

9036108-00

Содержание ExtremeSwitching VDX 6740








































































































































Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching VDX 6740, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды