Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 69

Страница: 69 / 135

3. Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb (29 cm-kg).

FIGURE 46

Attaching the rear brackets to the rack posts

Screws, 10-32 x 5/8-in., panhead Phillips

Retainer nuts, 10-32

Flush-rear (recessed) mounting

The flush-rear (recessed) mounting is similar to the flush-front mounting except that the brackets are reversed on the device.

CAUTION
The device must be turned off and disconnected from the fabric during this
procedure.

NOTE

The illustrations in the rack installation procedures show a 1U device, but the instructions are the same for a 2U device. The
illustrations in the rack installation procedures are for reference only and may not show the actual device.

Complete the following tasks to install the device in a four-post rack:

Attaching the front brackets to the rear of the device

on page 70

Attaching the extensions to the front of the device

on page 70

Installing the device in the rack

on page 71

Attaching the rear brackets to the extensions at the front of the device

on page 72

Attaching the rear brackets to the front rack posts

on page 74

Installing the Universal Four-Post Rack Kit (XBR-R000296)

ExtremeSwitching VDX 6740 Hardware Installation Guide

9036108-00

Содержание ExtremeSwitching VDX 6740








































































































































Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching VDX 6740, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды