Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 135

background image

LED patterns

The following table lists the port-side LEDs and the meaning of LED operation.

NOTE

For ports configured for FlexPort operation, LED patterns indicate operational status of GbE or Fibre Channel ports, depending
on type of transceiver installed and FlexPort configuration of port.

TABLE 3

Port side LED patterns during normal operation

LED name

LED color

Status of hardware

Recommended action

System power (one LED [green])

Off (no light)

System is off or there is an internal
power supply failure.

Voltage may be dropping below
specification.

Verify the system is powered on,
the power cables are attached, and
your power source is live.

Contact your service provider.

Steady green

System is on and power supplies
are functioning properly.

No action required.

System status (one bicolor LED
[green and amber])

Off (no light)

System is off or there is no power.

Verify the system is on.

Steady green

System is on and functioning
properly.

No action required.

Blinking amber/green

Attention.

Most likely a power supply or fan
assembly has faulted. Verify the
status and check all messages.

Steady amber (for more than 5
seconds)

A system fault has occurred or the
device is in an initialization state.

Check the management interface
and the error log for details on the
cause of the status.

Contact your service provider.

Ethernet Link (Management port)
(one LED [green])

Off (no light)

There is no link.

No action required.

Steady green

Link is present.

No action required.

Ethernet Activity (Management
port) (one LED [green])

Off (no light)

There is no activity.

No action required.

Blinking green

There is activity (traffic).

No action required.

VDX 6740

Ethernet ports

All user ports.

Off (no light)

Port is in no shut state and no cable
or transceiver present, no link, 40
GbE port in SFP breakout mode
(also referred to as 4x10 GbE
breakout mode) has no cable, or
license is not available for the port.

Insert SFP+ or QSFP with cable
connected to another port in no
shut state or connect cable to 40
GbE port.

Steady amber

Protocol down or no sync or 40
GbE port in 40G mode has no
cable.

Check the local port SFP+ or QSFP
or peer port SFP+ or QSFP and
cable.

Slow blinking amber

Port is shut or chassis disabled or
POST failed.

Enable the port.

Fast blinking amber

Port is faulted, goes into shut state.

Check messages for fault reason
and take necessary action.

Steady green

Link is present, no activity.

No action required.

Slow blinking green

Port is good except ISL is
segmented.

No action required.

Fast blinking green

Beaconing enabled.

No action required.

Flickering green

Online, frames flowing through the
port.

No action required.

VDX 6740T

and

VDX 6740

Ethernet ports

LED activity interpretation

ExtremeSwitching VDX 6740 Hardware Installation Guide

9036108-00

101

«
...
99
100
101
102
103
...
»

Содержание ExtremeSwitching VDX 6740








































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching VDX 6740

Бренд: D-Link Страницы: 357

Бренд: OFFICINE OROBICHE Страницы: 7

SANbox 5000 Series

Бренд: Qlogic Страницы: 8

PARAGON II Series

Бренд: Raritan Страницы: 1

Paragon Manager

Бренд: Raritan Страницы: 117

Бренд: Dataprobe Страницы: 3

Бренд: Panasonic Страницы: 206

iMcV-Giga-FiberLinX-II

Бренд: IMC Networks Страницы: 60

Бренд: IOGear Страницы: 1

Бренд: Black Box Страницы: 28

Бренд: Open Mesh Страницы: 2

Cooper Power Systems LCR 6200 RFN

Бренд: Eaton Страницы: 8

Бренд: Free-Way Switch Страницы: 6

Бренд: Net Generation Страницы: 38

Бренд: LEGRAND Страницы: 30

Бренд: N-Tron Страницы: 169

Smart Switch 2:1

Бренд: XTBA Страницы: 3

Бренд: Unipoe Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды