Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 119

Страница: 119 / 135

Power supply specifications (per PSU)

Power supply
model

Maximum output
power rating (DC)

Input voltage

Input line
frequency

Maximum input
current

Input line
protection

Maximum inrush
current

AC to DC - VDX
6740

XBR-250WPSAC-
F

XBR-250WPSAC-
R

250 W

100 - 240 VAC
(nominal)

90 - 264 VAC
(range)

50/60 Hz
(nominal)

47 - 63 Hz (range)

3.5 A

Line Fused

50 A peak @ 240
VAC at cold start
for < 10 ms, 15 A
peak for cycles 10
ms - 150 ms, <
3.5 A peak for >
150 ms

AC to DC - VDX
6740T

XBR-500WPSAC-
F

XBR-500WPSAC-
R

504 W

100 - 240 VAC
(nominal)

90 - 264 VAC
(range)

50/60 Hz
(nominal)

47 - 63 Hz (range)

6 A @ 100 VAC

7 A @ 85 VAC

Line Fused

30 A peak at cold
start & 50 A peak
at warm start for <
10 ms, 10 A peak
for cycles 10 ms -
150 ms, < 7 A
peak for >150 ms

DC to DC - VDX
6740

XBR-250WPSDC
-F

XBR-250WPSDC
-R

250 W

48Vdc (nominal)

40-60Vdc (range)

40-60Vdc with +
or - zero percent
tolerance

N/A

7.1 A

-Ve and return
fused

50 A peak for any
initial current surge,
or spike of 10ms
or less

DC to DC - VDX
6740T

504 W

48Vdc (nominal)

40Vdc-60Vdc
(range)

N/A

15 A

-Ve Fused

25 A peak @ 25°C

Power consumption VDX 6740 and VDX 6740T (idle configuration)

No optics or connections to ports and system booted up. Fans at nominal speed.

Model

@ 100 VAC input

@ 200 VAC input

@-48 VDC Input

Maximum number of
power supplies

Notes

VDX 6740

0.842 A

91 W

310.59 BTU/hr

0.473 A

96 W

317.42 BTU/hr

1.5 A

77 W

262.94 BTU/hr

Input current is for 1
PSU, Watts & BTUs/hr
are for two PSUs.

VDX 6740T

2.049 A

225 W

767.94 BTU/hr

1.05 A

219 W

747.46 BTU/hr

4.12 A

208 W

711.46 BTU/hr

Input current is for 1
PSU, Watts & BTUs/hr
are for two PSUs.

ExtremeSwitching VDX 6740 Switch Technical Specifications

ExtremeSwitching VDX 6740 Hardware Installation Guide

9036108-00

119

Содержание ExtremeSwitching VDX 6740








































































































































Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching VDX 6740, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching VDX 6740

Отзывы:

Похожие инструкции для ExtremeSwitching VDX 6740

Бренды по названию

Популярные бренды