Extreme Networks E4G-200 Скачать руководство пользователя страница 91

Страница: 91 / 120

Technical Specifications

E4G-200 Cell Site Router Technical Specifications
E4G-400 Cell Site Aggregation Router Technical Specifications
Power Supplies for the E4G-400 Router
E4G-200 Connector Pinouts
E4G-400 Connector Pinouts
Conformity Statements

This appendix includes specifications for E4G series routers and related components.

E4G-200 Cell Site Router Technical Specifications

Table 17: Physical Dimensions

E4G-200 router

Height: 1.75 inches (4.4 cm)
Width: 17.25 inches (43.8 cm)
Depth: 10.75 inches (27.3 cm) (Includes connectors and ground lug)

Clock/timing module

Height: 1.75 inches (4.4 cm)
Width: 2.5 inches (6.4 cm)
Depth: 8 inches (20.32 cm) (includes connectors)

T1/E1 module

Height: 1.75 inches (4.4 cm)
Width: 6.25 inches (15.9 cm)
Depth: 9.5 inches (24.1 cm) (includes connectors)

Table 18: Weight

E4G-200 router

7.14 lb (5.46 kg)

Clock/timing module

0.75 lb (0.34 kg)

T1/E1 module

2.0 lb (0.9 kg)

Table 19: Packaged Dimensions

E4G-200 router

Height: 5.25 inches (13.3 cm)
Width: 22.5 inches (57.2 cm)
Depth: 14 inches (35.6 cm)

E4G-200 CLK
Clock/timing module

Height: 3.0 inches (7.62 cm)
Width: 8.5 inches (21.6 cm)
Depth: 6.0 inches (15.2 cm)

T1/E1 module

Height: 4.5 inches (11.4 cm)
Width: 7.25 inches (18.4 cm)
Depth: 14.0 inches (35.6 cm)

E4G Routers Hardware Installation Guide

Содержание E4G-200

























































































































Результаты поиска

Содержание E4G-200

Отзывы:

Похожие инструкции для E4G-200

Бренды по названию

Популярные бренды

Extreme Networks E4G-200, Руководство по установке

Результаты поиска

Содержание E4G-200

Отзывы:

Похожие инструкции для E4G-200

Бренды по названию

Популярные бренды