manualshive.com logo in svg

Extreme Networks E4G-200, Руководство по установке, Страница: 42 / 120

Поделиться
Скачать
Extreme Networks E4G-200 Скачать руководство пользователя страница 42

3 Insert each stripped wire into the connector, as shown in 

the following figure

.

Make sure that no exposed part of the copper wire extends beyond either side of the connector.

Figure 20: Preparing a DC Power Cable

4 Tighten each retaining screw to 4.5 pound-inches (0.5 Newton-meters) to fasten the wire in place.

After the DC input cable is attached to the connector, it must be properly connected to the DC source
voltage at your facility by a qualified electrician.

Connecting the E4G-200 Router to DC Power

Before you connect the DC input cable to the power input socket on the E4G-200 router, the DC input
cable must be properly connected to the DC source voltage at your facility by a qualified electrician.

Caution
Connect the DC input cable to a DC main circuit breaker rated no greater than 15A. Provide
proper connection and strain relief on the DC input cable in accordance with all local and
national electrical codes.

1 Verify that the DC circuit is de-energized.
2 Align the power cable connector with the power input connector on the router and press the

connector firmly into place.

Installing an E4G Series Router

E4G Routers Hardware Installation Guide

42

Содержание E4G-200

























































































































Отзывы:

Нет отзывов