Extreme Networks E4G-200 Скачать руководство пользователя страница 53

Страница: 53 / 120

Figure 34: Installing a Summit 300 W DC Power Supply (Model 10933)

Figure 35: Installing a Summit 300 W DC Power Supply (Model 10934A)

If power supplies are not installed in both power supply bays, install a cover over the unoccupied bay.
The cover is required for maintaining proper system ventilation and EMI levels.

Connecting the Ground Cable

After installing the DC power supply (Model 10933 or 10934A), you must ground it before attaching it to
a power source.

Warning
Connect the ground cable before you connect any power cables.

Warning
Disconnect the ground cable after you disconnect all power cables.

1 Verify that the DC circuit is de-energized.
2 Attach an ESD-preventive wrist strap to your bare wrist and connect the metal end to an

appropriate ground point on the rack.

Installing an E4G Series Router

E4G Routers Hardware Installation Guide

Содержание E4G-200

























































































































Результаты поиска

Содержание E4G-200

Отзывы:

Extreme Networks E4G-200, Руководство по установке, Страница: 53 / 120

Результаты поиска

Содержание E4G-200

Отзывы: