Extreme Networks E4G-200 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 120

background image

zugangsbeschränkter Bereich kann beispielsweise nur mithilfe eines Spezialwerkzeugs, Schloss und
Schlüssel oder einer anderen Sicherheitsvorrichtung geöffnet werden.

Note
Da die Gebäudevorschriften in aller Welt unterschiedlich sind, empfiehlt Extreme Networks
dringend, sich bezüglich der korrekten Erdung und Spannungsverteilung für Ihre Installation
in Ihrem Land an einen Elektrofachbetrieb zu wenden.

Auswahl der Netzkabel

Im Lieferumfang von Extreme Networks-Produkten sind keine Netzkabel enthalten.

Ein für Ihr Produkt und Land passendes Netzkabel erhalten Sie entweder von Ihrem zuständigen
Extreme Networks Channel Account Manager oder Sales Manager oder im örtlichen Fachhandel. Die
Anforderungen an das Netzkabel entnehmen Sie Anhang B zu dieser Anleitung.

Hier finden Sie Ihren zuständigen Sales Manager oder Fachhändler:http://www.extremenetworks.com/
how-to-buy/how-to-buy.aspx

Note
Dieses Gerät ist nicht für eine direkte Versorgung von einem Spannungsverteilungssystem
vorgesehen, wo die Leiter-Leiter-Spannung den Wert von 240 VAC (2 Schutzerde),
wie zum Beispiel in Norwegen, Frankreich und anderen Ländern. Für derartige Anwendungen
wird ein Transformator empfohlen, um die Spannung auf einen Wert unter < 240 VAC (Leiter-
Leiter) herunterzutransformieren oder ein Anschluss an eine (P+N+Schutzerde)
Spannungsverteilung, wo die Spannung 240 VAC nicht überschreitet.
Alle Installationen müssen eine zuverlässige Erdung gemäß den nationalen Elektrovorschriften
vorsehen.

Wechseln und Entsorgen der Batterie

Die Batterien in Extreme Produkten sind gekapselt und dürfen nur durch qualifiziertes Extreme-
Wartungspersonal ausgewechselt werden.

1 Wenden Sie sich für den Austausch eines Produktes an das Wartungspersonal von Extreme

Networks. Versuchen Sie nicht, die Batterie selbst auszuwechseln.

2 Bei einer Missachtung dieser Anweisungen und dem Versuch, die Batterien eigenmächtig zu

wechseln, müssen folgende Richtlinien eingehalten werden, um eine mögliche Explosion zu
vermeiden:
a Tauschen Sie die Batterie nur gegen eine Batterie des gleichen Typs (wie vom Hersteller

empfohlen)aus.

b Entsorgen Sie die Batterie gemäß den Empfehlungen des Batterieherstellers.

LWL-Ports und optische Sicherheit

Folgende Sicherheitswarnung gilt für alle optischen Geräte, die in Extreme Networks-Geräten
eingesetzt werden und entweder herausnehmbar sind oder direkt in einem E/A-Modul oder im
Chassissystem eingebaut sind.

Safety Information

E4G Routers Hardware Installation Guide

89

«
...
87
88
89
90
91
...
»

Содержание E4G-200

























































































































Отзывы:

Нет отзывов

Похожие инструкции для E4G-200

Бренд: N-Tron Страницы: 101

Бренд: H3C Страницы: 1057

Бренд: 4IPNET Страницы: 97

Бренд: Planet Страницы: 20

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

Бренд: Lanner Страницы: 63

Бренд: Justec Страницы: 61

Бренд: Abocom Страницы: 2

Бренд: Schrack Technik Страницы: 2

ExpressBox2 EB2

Бренд: Magma Страницы: 74

Бренд: LevelOne Страницы: 146

Бренд: 8e6 Technologies Страницы: 94

Бренд: Draytek Страницы: 17

Бренд: Foxconn Страницы: 1

Бренд: ICP DAS USA Страницы: 8

Бренд: Allied Telesis Страницы: 2

Бренд: Planet Страницы: 431

Threat Analysis Reporter TAR HL/SL/MSA

Бренд: 8e6 Technologies Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды