manualshive.com logo in svg

Extreme Networks E4G-200, Руководство по установке, Страница: 24 / 120

Поделиться
Скачать
Extreme Networks E4G-200 Скачать руководство пользователя страница 24

Meeting Site Requirements

By carefully planning your site, you can maximize the performance of your existing network and ensure
that it is ready to migrate to future networking technologies.

The information in this chapter is intended for the system administrator, network equipment technician,
network manager, or facilities manager responsible for installing and managing the network hardware.

Operating Environment Requirements

Virtually all areas of the United States are regulated by building codes and standards. During the early
planning stages of installing or modifying your network, it is important that you develop a thorough
understanding of the regulations that pertain to your location and industry.

Verify that your site meets all environmental and safety requirements.

Building and Electrical Codes

Building and electrical codes vary depending on your location. Comply with all code specifications
when planning your site and installing cable. This section lists resources for obtaining additional
information.

For information about major building codes, consult the following organization:

International Code Council (ICC)
5203 Leesburg Pike
Falls Church, VA 22041 USA

www.iccsafe.org
www.sbcci.org

The organizations listed in 

the following table

 are authorities on electrical codes.

Table 13: Authorities on Electrical Codes

Organization

Address

Web Site URL

National Electrical Code (NEC) Classification (USA only)
Recognized authority on safe electrical wiring. Federal, state,
and local governments use NEC standards to establish their
own laws, ordinances, and codes on wiring specifications. The
NEC classification is published by the National Fire Protection
Association (NFPA).

NFPA
1 Batterymarch Park
Quincy, Massachusetts
02169
USA

www.nfpa.org

Underwriters’ Laboratory (UL) (USA only)
Independent research and testing laboratory. UL evaluates the
performance and capability of electrical wiring and equipment
to determine whether they meet certain safety standards
when properly used. Acceptance is usually indicated by the
words “UL Approved” or “UL Listed.”

UL
333 Pfingsten Road
Northbrook, Illinois
60062-2096
USA

www.ul.com

National Electrical Manufacturing Association (NEMA) (USA
only)
Organization of electrical product manufacturers. Members
develop consensus standards for cables, wiring, and electrical
components.

NEMA
1300 N. 17th Street
Rosslyn, Virginia 22209
USA

www.nema.org

Site Preparation

E4G Routers Hardware Installation Guide

24

Содержание E4G-200

























































































































Отзывы:

Нет отзывов